My TiO2 is not hiding well. What are the causes, and how do I fix it?
Work through three causes before you add more TiO2.
One — is the grade surface-treated? Untreated TiO2 wets out poorly in an oil phase, so it stays under-dispersed. Agglomerates act as much larger particles, scatter visible light less efficiently, and hiding actually drops; the film also shows white specks or mottling. More powder will not fix this — move to a treated grade and revisit the dispersion step at the same time.
Two — does the treatment match the system? Treated is not a single thing. AS (triethoxycaprylylsilane) suits formulas built on vegetable oils and esters: easy dispersion, low oil absorption, higher pigment loading. DSG (disodium stearoyl glutamate) is the amino-acid route — a softer, more emollient hand for mild or silicone-free positioning, but weaker water resistance than silicone treatments. TTS (isopropyl titanium triisostearate) gives very low oil absorption, disperses in a wide range of oils including polar esters, adds strong water repellency and a soft hand that compresses well — the usual pick for anhydrous systems and pressed powders. The wrong treatment leaves the powder just as hard to spread.
Three — are the other powders diluting the coverage? Talc and mica have a refractive index of only about 1.5–1.6, so a high loading thins out the overall hiding. The TiO2 has not failed; the total powder structure is the problem.
Fix in this order: confirm dispersion first (microscope the mill base for agglomerates), then confirm the treatment type, and only then consider raising the TiO2 loading. Do it in reverse and you pay twice — in cost and in skin feel.
The real ceiling on loading is skin feel. High-coverage formulas often run 15–20% TiO2; above that the formula turns dry and heavy, and pressed powders can go brittle. If you need coverage and a light feel together, a treated grade with better dispersion beats more powder.
Particle size is a grade-selection question rather than a troubleshooting one — see "Your rutile grades run from 210 to 420 nm. How does size change the result?" in this section.
| Market | Status | Basis and conditions |
|---|---|---|
| EU | Restricted | Annex IV / 143 (colorant); Annex VI / 27 and 27a (UV filter); Annex III / 321 (fine powder) — UV filter up to 25% (27 and 27a combined). Nano form must not be used in applications that may expose the lungs by inhalation. Fine powder with 1% or more of particles of aerodynamic diameter 10 micrometres or less: 25% in loose face powder, 1.4% (consumer) or 1.1% (professional) in aerosol hair products, and no lung-exposing applications otherwise. |
| UK | Restricted | Retained EU law, same entries — Wording carried over from the EU entries. |
| US | Restricted | 21 CFR 73.2575 (colour additive); 21 CFR 352 (OTC sunscreen active) — Up to 25% as an OTC sunscreen active. No federal nanomaterial-specific restriction in cosmetics. |
| China | Restricted | Safety and Technical Standards: permitted colorant; permitted UV filter 25% — Nano form requires separate registration and labelling. |
| Japan | Restricted | Quasi-drug: UV scatterer handled as a quasi-drug additive — No separate concentration ceiling, but an SPF or PA claim requires quasi-drug approval, and there the UV scatterer is handled as an additive that must meet the quasi-drug ingredient specification. Used purely as a colourant or bulking agent, no approval is needed. |
| ASEAN | Restricted | ACD Annex IV (colorant) and Annex VII (UV filter, 25%) — Same 25% ceiling as the EU. |
| Korea | Restricted | MFDS permitted colorant; permitted UV filter 25% — Nano form must be declared. |
| Canada | Restricted | Hotlist: permitted colorant and sunscreen active — Sunscreen monograph limit 25%. |
Swipe the table sideways for the full basis column →
Watch: The EU Carc. 2 (inhalation) classification of powder forms was annulled and the annulment was confirmed by the Court of Justice on 1 Aug 2025 — no CMR classification currently applies. Separately, the food-additive ban (E 171, Regulation (EU) 2022/63) concerns food only and does not affect cosmetic use; the SCCS oral-care opinion is still pending.
Checked November 2026. Summary only — every material in the same format. Not legal advice; verify before labelling.