You are using an outdated browser. For a faster, safer browsing experience, upgrade for free today.

Cosmetic Powder Knowledge Base

279 answered questions, filed under 9 sections and 25 topics. Every answer has its own page — bookmark it, forward it to a colleague, or cite it as a technical reference.

All answers279

Formulation & Process

Pressing crumble, pilling, white cast, lipstick sweating — what to adjust, by symptom.

001Why does my pressed powder crumble and how do I fix it?In most cases the problem is particle size distribution and the ratio of platy to spherical powders, not a lack of binder. Raise the fine fraction (D50 8-15 um) above roughly 35% and add 3-8% hexagona…
002Is pilling in liquid foundation a powder problem?Pilling in liquid foundation is, in most cases, not a problem with the powder itself — used on its own, powder almost never produces pilling. The usual cause is incompatibility between raw materials: …
003Which powders give a natural soft-focus effect?Soft focus means scattering light at the skin surface instead of reflecting it directly. At the powder level that requires two things: a particle size distribution close to the wavelength scale, and s…
004How do I reduce white cast and pilling in mineral sunscreen?White cast comes first from refractive index contrast and particle size, and only second from the formula. Nano TiO2 and ZnO in the 30-50 nm range scatter far less visible light; above roughly 100 nm,…
005How do I stop lipstick from sweating in summer?Sweating is the bullet structure collapsing at elevated temperature, caused by insufficient binding between the oil phase and the powders. The most direct fix is replacing part of the talc or mica wit…
006How do I keep coverage when reducing powder loading?Heaviness is rarely about total powder loading; it is about insufficient hiding power per unit weight, which forces you to over-dose. Switching to more efficient powders lets you cut total loading whi…
007Which powder should I use for oil control, silica or talc?Go with porous silica. Talc is better at slip and as a filler — the two are not in the same league for sebum absorption. Porous silica traps sebum inside its interconnected pore network and typically …
008My liquid foundation separates and settles over time. How do I fix it from the powder side?Settling comes from the density gap between the powder and the liquid phase, combined with poor wetting of the powder surface. Thickeners only delay it. There are three powder-side levers. First, part…
009High oil-absorption powder makes the finish feel dry. How do I rebalance it?The problem is not high oil absorption as such — it is that the powder strips oil from both the formula and the skin surface. The fix is to reduce the effective absorbing surface rather than simply cu…
010Which powders should I combine for a matte finish?Matte needs three things at once: high oil absorption, high diffuse reflection, and no glossy platelets. A single powder rarely delivers all three cleanly. The workhorse is porous silica, which handle…
011How do I choose pore size for oil absorption?Pore size decides two things: how fast oil goes in and how much the particle can hold. Three bands cover most work. Small pores at 5-15 nm with 300-500 m2/g surface area exert strong capillary force, …
012What does powder need to deliver eight hours of wear?Powder alone rarely delivers eight hours. Three conditions have to hold at the same time. First, enough absorption capacity. Start from sebum output: oily skin produces roughly 1-2 mg per square centi…
013Can oil control and moisturising coexist?Yes, but through selective absorption rather than a higher absorption dose. The conflict is that powder cannot tell sebum from the emollient oil in the formula, so it takes both, and oil control ends …
014How should powder differ between oily and dry skin formulas?The two logics are close to opposite. One oil-control platform cannot serve both skin types without leaving one side unhappy. For oily skin: high absorption with porous silica at 5-8%, mostly large po…
015How do I build a blended oil-absorption system?One powder is usually not enough, because absorption has to meet three conflicting demands at once: absorb fast, hold a lot, and not collapse once loaded. Divide the work three ways. Small pores with …
016Does hydrophobic treatment improve oil control?Usually yes, but not because it absorbs more. It absorbs more selectively and keeps what it takes. There is a cost, and it should be planned for. Three benefits. First, selectivity: a hydrophobic surf…
017What powder changes help wear hold up in summer heat?Three changes happen at once in heat: sebum output rises, oils in the formula soften, and sweat washes across the film. Above 32 C, sebum can run 50-100% higher than at 20 C. First, raise absorption c…
018How do I build a water- and sweat-resistant powder system?Three things have to work together: hydrophobic powder, a water-durable film, and few hydrophilic ingredients. Any one alone is not enough. First, hydrophobic powder. Silicone-treated grades are the u…
019Does powder affect lipstick transfer?It matters, but powder is not the main variable. Transfer is set largely by the film-forming system and the wax ratio, with powder as a secondary adjustment. Being clear about this saves effort, becau…
020Can powder choice stop touch-ups from caking and piling?Yes, but first separate the causes. In most cases the powder is not the problem; the first layer is already saturated with oil. Cause one, saturation. Four hours in, the powder has absorbed all the se…
021How should setting spray and oil-control powder be layered?The two conflict at one point: the film a setting spray leaves seals the absorption channels in the powder, so oil control drops. The order should follow the goal. Powder first, then spray, is the com…
022Shine appears four hours in. Which powder do I change first?Four hours is the classic signature of insufficient absorption capacity rather than insufficient speed. A speed problem shows up at one to two hours. So start by adding capacity, not by reaching for a…
023How do I balance caking and dryness after oil absorption?This is the standard side effect of a high-absorption formula, and it works through two mechanisms. After application, particles saturated with sebum stick together into clumps. During storage, the sa…
024Do oil-control powders absorb oil from the formula itself?Yes, and it is the most common hidden failure in oil-control formulas. A powder cannot tell sebum from formula oil; it absorbs whatever touches it. This happens in two stages. During storage, powder a…
025Is there a maximum powder load in long-wear foundation?Yes, and the ceiling depends on the format. Liquid foundation runs 15-22%, cushion 18-25%, cream foundation up to 25-30%. Go past those bands and the problems are predictable. Three consequences past …
026The pearl in my eyeshadow looks dull and the colour turns grey. What should I change?Check particle-size matching first, then the opacity of the base powders, and only then the pearl loading. Done in the other order it usually gets greyer. Step one: match platelet size to the base par…
027Can powder selection fix chipping edges and poor pickup?Partly. Chipping in a multi-pan palette behaves differently from a single pan: most of it sits at the boundaries between pans and at the rim. That is an edge effect — the press head transfers pressure…
028Is grittiness in lip mud caused by coarse powder?Check dispersion before blaming particle size. In practice about seven out of ten "gritty" complaints turn out to be agglomerates, and an agglomerate behaves like a particle several times larger than …
029What does powder do for transfer-resistant wear?Powder helps in three places, and none of them is adhesion. First, it takes up excess oil. Transfer is oil from the lips moving to the cup wall, so absorbing free oil reduces what can transfer. Spheri…
030How do I stop a clay mask from drying tight?The tightness is usually not about total oil uptake but about how steep the uptake curve is: the mask pulls oil and water out within minutes and the skin reads that as tight. Three powder-side levers.…
031My cream turns coarse and unstable after adding powder. What now?Three causes, in order of how often they turn up. First, surface treatment incompatible with the emulsifier system. Hydrophobically treated powder (SI, AS) has an oil-loving surface; if the emulsion r…
032Which purity indicators matter for skin care powders?"Purity" is not a single number in a powder raw material. Split it into four groups. Group one, hygiene: heavy metals (lead, arsenic, mercury, cadmium) and microbiology (total aerobic count, mould and…
033How do I verify dry powder blend uniformity, and how many sample points do I need?Do not judge uniformity by eye. Use one sensitive indicator, multiple sample points and RSD. Pick the indicator that responds most to imperfect mixing: colour difference where the blend is coloured (w…
034How does powder selection change in anhydrous and solid-cleanser formats?With no continuous water phase, the powder stops being a filler and becomes part of the structure, so the selection logic changes with it. First, do not chase high oil absorption. A foundation wants a…

Powder Materials

Boron nitride, spherical silica, mica, talc and pigments — how to choose, which system each fits.

035What does boron nitride actually do in cosmetics?Hexagonal boron nitride is a multifunctional platy powder: it delivers lubricity, press strength, lustre and thermal conductivity at the same time, which is hard to replicate with a single alternative…
036What is the difference between spherical and regular silica?The difference is shape and porosity, and that directly determines oil absorption, skin feel and optical behaviour. Regular silica consists of irregular particles and agglomerates; spherical silica is…
037Why are formulators moving away from bismuth oxychloride?Bismuth oxychloride was once the workhorse for pearlescent effects, with strong lustre and good coverage, but photostability is its unavoidable weakness: it darkens and greys under UV and strong light…
038Can mica and talc be substituted for each other?Not on an equal-weight basis. Their functional profiles differ: mica is platy and provides lustre and adhesion, while talc is platy but softer, providing slip and oil absorption with weaker coverage. …
039What is the difference between wet-delaminated and dry-milled powders?The core difference is platelet integrity and aspect ratio. Wet delamination cleaves along the platelet planes in a liquid medium, causing little damage and yielding a high aspect ratio. Dry milling r…
040How do I choose between triethoxycaprylylsilane, PDMS and stearic acid treatments?Choose based on the continuous phase: water-in-oil, oil-in-water, or anhydrous. Surface treatment exists to make the powder compatible with that phase. Triethoxycaprylylsilane suits water-in-oil and a…
041How is oil absorption actually measured, and is a higher value better?Oil absorption is measured to GB/T 5211.15 or ISO 787-5: oil is added dropwise to the powder and worked in until the paste can be lifted as a single mass without sticking to the plate. The result is e…
042What is the relationship between specific surface area and oil absorption?Broadly positively correlated, but not linear, and porous grades deviate most. BET specific surface area measures the total accessible area including pore walls; oil absorption measures how much oil t…
043How do I balance whiteness and coverage, and what happens if I overload titanium dioxide?Whiteness and coverage follow different curves: coverage depends on refractive index contrast, whiteness on reflectance. Titanium dioxide maxes out both at once, so the problem is rarely not white eno…
044How do I match mica particle size to the gloss level I want?Mica gloss comes from specular reflection off its platelets. The larger and more intact the platelet, the larger each reflective surface and the more sparkle; finer grades read as a soft silky sheen. …
045What do Halal, Kosher and Vegan certification mean for a powder, and what extra paperwork is needed?The three schemes do not audit the same thing, and treating them as one file wastes money. A Halal certificate looks at two ends: whether the material contains animal-derived content or alcohol, and w…
046Which powder properties should I screen out for a formula for reactive, redness-prone skin?First the boundary: whether the finished product can carry a claim is a matter for the safety assessment and the efficacy evidence. What the ingredient side can do is screen out the known risk factors…
047Is R457 the same figure as CIE whiteness, and can I compare them?Whiteness is a convention, not a number. Comparing values from different conventions gives a wrong answer. Two dominate. R457, also called ISO brightness, measures reflectance in the blue at 457 nm an…

Regulation & Compliance

EU, Japan and China requirements, export documents, and how restricted substances are verified.

048Is talc still allowed in cosmetics, and what are the restrictions?Yes, but regulation is tightening and requirements differ significantly by market. The single most important rule is that cosmetic talc must be confirmed free of asbestos, a baseline shared by all maj…
049Can nano titanium dioxide still be used in the EU?Yes, but powder spray formats that could be inhaled are effectively excluded. The EU restriction logic for nano TiO2 and nano ZnO centres on inhalation risk, not dermal application. That means creams,…
050What are the heavy metal limits for cosmetic powders?China's Safety and Technical Standards for Cosmetics sets limits of lead at or below 10 mg/kg, arsenic at or below 2 mg/kg, mercury at or below 1 mg/kg and cadmium at or below 5 mg/kg. These apply to …
051What documentation is needed to export cosmetic powders to the EU?Three categories matter most: composition and regulatory compliance statements, safety assessment support data, and explicit nano labelling. For composition, provide full INCI names, CAS numbers and a…
052What extra requirements apply to powders in children's cosmetics?The core principles for children's cosmetics are simplified formulas, safe ingredients and controlled use scenarios. At the powder level that translates into fewer unnecessary colorants, avoiding inha…
053Do powder raw materials need microbiological testing?Yes, but the focus differs from liquid raw materials. Powders have low water activity, so microbial proliferation is limited and risk comes mainly from cross-contamination during production and recont…
054How should INCI names for cosmetic powders be written, and what if the Chinese and English names do not match?Always work from the English INCI name. Chinese names are reference translations, mismatches are normal, and you should never derive the INCI from the Chinese name. There is no single official Chinese…
055A customer is asking for REACH and asbestos reports. What documentation can a powder supplier typically provide?Powder suppliers generally cover three categories: basic quality documents, regulatory compliance statements, and third-party test reports. Not every grade has all of them, so confirm before you order…
056What data should a powder supplier provide for a full safety assessment?A full safety assessment asks one question: can the exposure be quantified? For a powder that means four data groups, not a certificate of analysis. Composition first — INCI name, chemical identity, p…
057Does the EU microplastics restriction (2023/2055) affect cosmetic powders?The restriction covers synthetic polymer microparticles, not powders as a category — so split the question into inorganic and organic. Out of scope: talc, mica, kaolin, silica, boron nitride, titanium…
058How should a powder supplier support California Prop 65 labelling?Prop 65 is a right-to-know law, not a ban list: a listed substance above its exposure threshold triggers a warning, below it does not. So the ingredient side does not need to avoid a word — it needs t…
059How much does a mineral powder contribute to an ISO 16128 natural origin index?Start with the two tiers: ISO 16128 distinguishes natural origin from natural, and almost every mineral powder sits in the first. The index is a mass-weighted calculation over the components, not a mo…

Ordering & Samples

Sampling, MOQ, lead times, how quotes are built, custom surface treatment — confirm before ordering.

060What is the sampling process and how long does it take?The usual flow is: describe the application and requirement, we recommend matching grades, samples ship, you run a bench trial. Samples are typically 100-500 g, enough for several small-scale trials. …
061What is the minimum order quantity?For standard grades the MOQ follows the packaging format, typically one 25 kg drum, with some higher-value grades available in 5 kg or 10 kg packs. Custom-treated powders carry a higher MOQ because su…
062Can you customise surface-treated powders for my formula?Yes, customisation is one of our core capabilities. Adjustable variables include the treatment chemistry and coating level, the particle size distribution, and the blend ratio with other powders. The …
063What are typical lead times and are standard grades in stock?Standard grades are normally stocked, with shipment scheduled after order confirmation. Custom grades are queued against the treatment process and take noticeably longer. Three factors drive lead time…
064Can you provide COA, MSDS and TDS?Yes, all three. The COA is issued per batch with measured values for that batch; the MSDS follows the standard format; the TDS gives typical properties and application guidance. Do not confuse them. T…
065How is pricing structured, and why do quotes for the same spec differ so much?Powder pricing has four components: raw material cost, processing method, particle size and purity control, and surface treatment. For the same nominal specification, most of the spread sits in the la…
066Imported powder is getting expensive or unavailable. How should I evaluate a domestic alternative?Start with risk, not performance. List what could go wrong before you discuss specifications. Four steps. First, lock down the critical parameters: identify the two or three properties that actually d…
067How close are domestic fumed silica suppliers to Evonik and Cabot?For standard fumed silica the gap has largely closed. What remains sits in high purity, specialized surface treatment, and batch consistency. Where domestic product matches: specific surface area of 1…
068FOB, CIF or DDP — which Incoterm works best for exporting powder?The three terms divide where costs are paid and where risk passes. Choosing badly does not just cost money; it leaves nobody responsible when something goes wrong. FOB passes risk once the goods are o…
069How should payment terms be set on a first powder order?Powder is a low-value, high-weight, tonnage product, so payment terms are about who carries the working capital, not about trust. Three structures cover most cases. A 30% deposit by T/T with the balan…

Production & QC

How D50 is measured, batch-to-batch control, preventing agglomeration, retention samples, issue handling.

070How is D50 measured, and can results from different labs be compared?D50 is the median of the cumulative particle size distribution, usually measured by laser diffraction. Different instruments and different dispersion conditions can produce quite different numbers. Th…
071How do you control batch-to-batch variation?Three things: a stable raw material source, fixed process parameters, and per-batch testing before shipment. Powder production is most exposed to changes in deposit or supplier; once the impurity prof…
072Why do powders agglomerate and how can it be prevented?There are two types, soft and hard agglomerates, and they require completely different responses. Soft agglomerates are held by van der Waals forces and static and can be broken by dispersion. Hard ag…
073What cleanliness class is the production environment?Cleanliness control for powder production differs from liquids: powders do not readily support microbial growth, so dust control and cross-contamination prevention are the focus. Key control points in…
074Do you keep retention samples and for how long?Yes. Retention samples are kept for a defined period after each batch ships, with the duration depending on product type and customer agreement. Custom grades are retained longer because they correspo…
075How are quality issues handled?Step one is always to freeze the information: keep the physical sample from the affected batch, record the use conditions, and establish how the anomaly can be reproduced. Without those three, any con…
076My loose powder flies everywhere and does not adhere well. How do I fix it from the powder side?Flying powder is mostly excess fines plus static, while poor adhesion is insufficient affinity between powder and skin. They often appear together but have different causes. Start with the particle si…
077Do cosmetic powders need sterilisation, and what does each method cost?Start with the conclusion: not every powder needs sterilisation. Powders are low in moisture and low in water activity, and the microbial load usually comes from packaging, the environment and storage…
078How do I control metal contamination in powder, and where do the magnet and detector go?Metal contamination comes from three places: wear on equipment (mill liners, torn screens, screw flight edges), the raw material itself, and packaging (staples, clips, bag seals). Control points follo…

After-Sales Support

Caking on arrival, batch colour drift, mismatched retest data, dispersion failures, storage spoilage — how to judge, and what to do next.

079The powder arrived caked. Can this batch still be used?Separate soft caking from hard caking first. If the lumps break under light hand pressure and leave no hard residue on a 40-mesh sieve, it is soft caking — usually caused by transport vibration plus s…
080This batch looks visibly different in colour from the last one. How much colour difference counts as a reject?Rule out sample preparation first: a finer particle size reads whiter and brighter, and pressing pressure and substrate shift the numbers considerably. Only ΔE measured under identical preparation — s…
081The bulk shipment does not perform like the sample we approved. Where do we start?Four checks, in order — most issues are found before the fourth. 1. Same specification: grade, surface treatment type and coating level, particle size band. One difference changes the hand feel. 2. Fo…
082Our retest gives different D50, whiteness and oil absorption values from your COA. Which one stands?Compare test conditions before comparing numbers. D50 depends on dispersion medium, dispersant type and dose, ultrasonic power and duration — a 10–20% spread between condition sets is common. Whitenes…
083Our incoming test flagged abnormal microbiology or heavy metals. Does the whole batch have to be scrapped?Establish whether the finding holds before deciding on disposition. Three things to confirm: whether sampling was representative (multi-point, avoiding the surface layer), whether the test method matc…
084The powder will not disperse in our system and leaves specks. Is it the material or the process?An isolation test settles it: disperse this powder alone in the same medium, with no other powders and no other additives. If specks remain, the cause is the powder itself (hard agglomeration or moist…
085How long can the powder be stored, and can an expired batch be downgraded to another use?Unopened, sealed and stored cool and dry (≤30 °C, RH ≤60% recommended), standard grades carry a 24-month shelf life; the COA marking governs. Past shelf life does not automatically mean unusable, but …
086After switching to a different base oil, the surface-treated powder floats. Is the treatment layer coming off?Usually it is not the coating coming off — it is a change in compatibility. Surface treatment (silicone, fluorine, amino acid) sets the hydrophilic-lipophilic balance of the powder. Changing the base …
087The packaging was damaged in transit and the powder is contaminated. What now?Three things on site: do not open the bag, do not decant, do not sieve. Quarantine the whole package and take four photographs — outer carton, breach, batch label, powder condition. Send us three thin…
088If we need technical support, should we send samples or arrange a site visit?Both are possible, and anything that can be resolved remotely does not need a visit. Samples: 500 g each of the same-batch retention sample and the problem sample, with system composition (redacted is…
089On what basis is a quality complaint judged, and what is the process?Three bases: the quality agreement or purchase contract signed by both parties, the specifications and test methods stated on the COA, and the agreed arbitration testing route. Where none of the three…
090How do we confirm that only one batch is affected?Through batch traceability. Our records cover three things: raw material lot, production batch, and retention sample plus shipment routing. Given a batch number, we can tell which customers received t…
091After a batch fails, should it be returned, replaced or accepted at a discount?The remedy follows from whether the material can still be used, not from who is more at fault. Return: the lot goes back or is destroyed in place. Freight, customs and destruction costs have to be all…

Matrix Powders

Particle size, oil absorption and press behaviour across the mineral fillers.

Wet-Stripped Boron Nitride15 answers

092Which Kingbornit series should I use for Europe, the US and Japan?Start from the market, then pick the particle size. All three series behave the same in the formula — they differ only in how much soluble boron the powder can release. Kingbornit 7000 (7006 / 7012 / …
093How do I choose between the 6, 12, 15 and 20 µm grades?Choose by the skin feel you are targeting, then check the coverage requirement. 6 µm (7006, surface area 9) has the highest surface area in the range and gives the most pronounced soft-focus and cover…
094What loading do you recommend in pressed powder and in loose powder?A common starting point is 3–8%, adjusted upward for skin feel. Loadings above 15% are rare. At low loading boron nitride mainly improves spreading and slip, and contributes little to compact strength…
095Can boron nitride replace talc, and at what ratio?Partly, and not one-for-one. Replacing 20–50% of the talc is usually workable in pressed and loose powders; full replacement is not. The platy structure is similar to talc and slip is typically higher…
096What is soluble borate, and why does the grade matter for export?It is the fraction of boron that can leach out of the powder, and it is what market-specific questionnaires ask about — not the total boron content. Boron nitride itself is chemically inert. Residual …
097The coarser grades have lower specific surface area. Does that change how they behave?Yes, and it is the main reason size selection matters more than series selection. Surface area drives how much binder and oil the powder takes up, and how much light it scatters. Going from 6 µm (area…
098Does boron nitride work in liquids — foundations, creams, lip products?Yes, but for a different reason than in powders. In liquids it is a texture and slip modifier, not a structure former. The plates orient during application and reduce the drag you get from high oil-ab…
099What comes with each lot, and what can you provide for a REACH or customer questionnaire?Every lot ships with a COA reporting the specification figures for that batch, including the soluble boron figure for that grade — quoted as soluble borate % on the 7000 and 3000 series and as boron l…
100What is the minimum order and lead time for a standard grade like 7012?Standard grades are normally stocked and ship in small quantities for sampling; production volumes are quoted per order. Lead time depends on grade and quantity rather than being fixed. In practice: s…
101How does boron nitride affect coverage and whiteness?It does not add coverage, and it is not a whitening filler. Its refractive index is close enough to typical binder and filler systems that it scatters little. What it does is make the finish look soft…
102Boron nitride or a silicone elastomer powder — which gives better slip?They give different kinds of slip, and most premium powders end up using both. Boron nitride is a hard, platy mineral. The glide comes from platelets sliding over each other, and the afterfeel is dry,…
103Do I need the SI-treated boron nitride, and what does the treatment actually solve?The untreated powder is already hydrophobic enough for most anhydrous systems, so the treatment is not about wetting. It is about dispersion stability and film behaviour. The SI grade carries a surfac…
104The boron nitride feels gritty in my formula. What is going wrong?Almost always dispersion, not the grade. The platelets stack face to face and form soft agglomerates that a low-shear mixer will not break, so you feel clusters rather than individual platelets. Two f…
105How do I combine boron nitride with mica and silica?By function, not by ratio. The three do different jobs and substituting one for another is how talc-free projects go wrong. Boron nitride is the lubricant: 2–8% buys glide and pressability. Mica is th…
106Can boron nitride do anything useful in a sunscreen?It is not a UV filter and contributes essentially nothing to SPF. What it does is fix the sensory problems that make people under-apply. At 1–4% in a mineral sunscreen it improves spreadability, reduc…

Spherical Porous Silica14 answers

107How do I choose between oil absorption 60 and 300?By how much oil you need taken out of the formula, and how dry you can afford the finish to feel. Low oil absorption (Kingsica S060 at 60, TR070SI at 70) suits formulas that already contain enough oil…
108What is the practical difference between S201 and S300, and between S202 and S302?Particle size is nearly the same; oil absorption is not. S201 is 7 µm at 200, S300 is 7 µm at 300. S202 is 5 µm at 200, S302 is 5 µm at 300. So these pairs let you change oil absorption without changi…
109Which grade gives soft-focus, and at what loading?The fine, mid-absorption spherical grades — 2028 at 2 µm and 3028 at 3 µm — are the usual starting point, typically at 2–6%. Soft-focus comes from the spherical shape and the pore-size distribution ra…
110Which grades are for scrub and cleansing textures?The PC series — PC20 (20 µm), PC100 (100 µm), PC150 (150 µm) and PC200 (200 µm), at oil absorption 100–130. For scrubs the particle size sets the sensation: 100–200 µm reads as a clearly perceptible s…
111Does higher oil absorption mean better oil control on skin?Not necessarily. It means the powder takes up more oil in a beaker, which is a formulation property and only an indicator of what happens on skin. On skin, oil control depends on how much powder is ac…
112My formula feels tight and dry after adding silica. How do I rebalance it?Drop the oil absorption first, then the loading, then add back slip. High-absorption silica removes part of the oil phase along with the sebum, so the film ends up under-plasticised. Moving from a 300…
113How do I stop silica from agglomerating in the premix?Wet it out before it goes into the main batch, and keep the shear high enough while it disperses. Spherical porous silica has a large internal pore volume, so it pulls binder and oil into the pores qu…
114What documentation is needed to ship silica to the EU and the US?COA per lot, TDS and SDS are the baseline. Beyond that, the requirement depends on the form and on how the customer's own product is classified. Two questions come up most often. First, whether the ma…
115Is silica a direct replacement for talc in a talc-free reformulation?It can support the claim, but it is not a texture-for-texture swap. Talc is platy and provides slip plus moderate oil absorption. Spherical silica provides oil absorption plus ball-bearing glide and s…
116What are the MOQ and lead times for Kingsica grades?Stocked standard grades move quickly at sample scale; the commercial quantity and lead time are quoted per grade and destination. The wide grade range — OA from 60 to 300, size from 2 to 200 µm — mean…
117What particle sizes are available, and how do I convert mesh to microns?Our range runs from roughly 2 µm to 200 µm. The mesh figure some suppliers quote is a screen size, not a particle size, and the conversion is approximate: 325 mesh is about 44 µm, 800 mesh about 18 µm…
118Is cosmetic-grade silica safe on skin, and what should I check in the documentation?The material is amorphous synthetic silica, not crystalline quartz, and that distinction is the whole safety story — crystalline silica is the respirable hazard, amorphous silica is not, and cosmetic …
119Oil absorption or specific surface area — which number should drive my choice?Oil absorption is the number to formulate with; specific surface area is the number that explains it. The two track each other closely, because more surface means more oil held on it, so a grade at 30…
120How does silica compare with talc and kaolin for oil control?Silica absorbs the most per unit weight, kaolin next, talc the least — and that ordering is exactly why talc-free reformulations keep running into shine. A porous silica at 200–300 oil absorption take…

Titanium Dioxide13 answers

121Rutile or anatase: which one should I start with?Rutile for almost everything, anatase only where you want a specific optical effect. Rutile scatters light more efficiently and is the grade the industry builds coverage around, so it reaches the same…
122Your rutile grades run from 210 to 420 nm. How does size change the result?Smaller particles give more covering power per kilo but scatter less light back at you; larger ones give a brighter, cleaner white and easier wetting. T-60 at 210 nm and CR50 at 250 nm and T-90 at 280…
123What is the difference between aluminium hydroxide coating and aluminium hydroxide plus silica?Alumina alone gives photostability and dispersion; adding silica on top improves the surface's resistance to the photoactive reaction that TiO2 can trigger in a formula. That matters when the TiO2 sit…
124What loading do you see in foundation, pressed powder and sunscreen?Foundation usually lands at 5–12%, pressed powder at 3–8%, and sunscreen at whatever the SPF target dictates — often 3–8% for a moderate SPF in combination with an organic filter, higher for mineral-o…
125Is your TiO2 nano or non-nano? How do I document that?It is non-nano. The rutile grades are specified at 210–420 nm mean particle size and the anatase grades at 200–220 nm, all well above the 100 nm threshold used in most nano definitions. For a customer…
126My coverage dropped after switching to a finer grade. Why?Because fines that are not fully dispersed act as light scatterers in the wrong size range — they dull the film instead of whitening it. Going from a 400 nm grade to a 210 nm grade roughly doubles the…
127Does TiO2 whiten as much in a water-based system as in an anhydrous one?Less, and the gap is bigger than most people expect. TiO2 needs air voids around the particle to scatter efficiently. In an anhydrous base the oil wets the surface only partially, leaving those voids;…
128What paperwork comes with each lot?A batch COA, the TDS, and the SDS. Additional documents — heavy metal statements, allergen declarations, non-nano statements, REACH registration status — are issued on request against the specific gra…
129Which grade should I use in a compact where hardness matters?T-48 or T-02 in rutile, or T-01 in anatase. Hardness in a pressed compact comes from particle packing and from the binder, and coarser particles pack into a denser, stronger structure. The 400–420 nm …
130What are MOQ, lead time and packaging?MOQ is typically 25 kg for a stock grade and 100–200 kg for a production run of a non-stock grade. Lead time is roughly 7–15 working days depending on grade and quantity; stock items ship sooner. Stan…
131My TiO2 leaves a chalky white cast. How do I fix it?White cast is TiO2 doing its job too well in the wrong place. It scatters across the visible spectrum, and past a certain loading that scatter reads as a white film rather than as coverage. Three leve…
132Does TiO2 cause photocatalytic degradation, and how do I control it?Uncoated TiO2 is photocatalytic. It generates radicals under UV, and in a formula that shows up as fragrance breakdown, colour fading and, in the worst case, rancidity in the oil phase. This is a real…
133Is TiO2 permitted in lipstick, and does it change the feel?Yes, and it is common — it is what gives a lipstick opacity and makes a red read as red rather than as a stain. Two caveats. The regulatory one: TiO2 for lip use is permitted in most markets, but the …

Calcined Kaolin11 answers

134Calcined or hydrous kaolin — what is the actual difference in the formula?Calcination drives off the water of crystallisation and sinters the platelets, which raises whiteness, hardness and oil absorption. Hydrous kaolin stays softer and is used where you want a clay that d…
1355000 at 2 µm or GL03 at 3 µm?2 µm if you want maximum oil absorption and a matte finish; 3 µm if you want easier dispersion and a less dry feel. The finer grade has more surface per gram, so it takes up more sebum and gives a fla…
136Why is calcined kaolin used for press strength?Because the calcination step creates a harder, more angular particle that interlocks under pressure instead of sliding past its neighbours. Soft platy fillers such as talc and mica slide, which is wha…
137How much can I load, and what does it do to skin feel?5–15% is the usual band. Below 5% you mostly get a mattifying effect with little structural contribution; above 15% the dryness becomes the dominant sensation. At 8–12% you get both the oil absorption…
138Does higher calcined kaolin loading mean better oil control?Up to a point, then it plateaus and starts to cost you comfort. Oil absorption rises with loading, but once the powder is saturated the excess oil simply sits on top of the film, and the dry feel of a…
139Can calcined kaolin replace part of the talc in a pressed powder?Yes, and it is one of the easier substitutions — 20–40% of the talc is a reasonable starting point. Both are platy aluminosilicates, so the texture translates without a big reformulation. What changes…
140Is the whiteness stable across lots?The specification holds whiteness within a defined band, but calcined kaolin is a natural-mineral product, so there is lot-to-lot variation inside that band. For a tinted product, that matters more th…
141What does the 'global regulation compliant' series change?It is produced and tested against a tighter heavy-metal profile, which is what most market-specific cosmetic questionnaires actually ask about. The base grade meets the general cosmetic specification.…
142How does it disperse, and what equipment do I need?It wets out slowly but disperses cleanly once wetted — the difficulty is the initial wetting, not the breakdown. In a dry powder blend it is simply blended. In a slurry or a cream it needs shear: a hi…
143What is the MOQ and how is it packed?25 kg per bag as standard, with 500 kg jumbo bags for volume orders. MOQ for a stock grade is 25 kg; a non-stock grade is typically 100–200 kg. Lead time runs about 7–15 working days. Samples are 1 kg…
144My pressed powder crumbles or caps after I added kaolin. What went wrong?Usually too much kaolin, or too little binder to compensate for it. Calcined kaolin is a strong oil absorber, so it takes binder out of circulation — the pan is under-bound even though the binder perc…

Talc13 answers

145Your grades run from 5 to 16 µm with oil absorption from 40 to 81. How do I choose?Choose by oil absorption first, particle size second — the two move together but not perfectly, and oil absorption is what drives the skin feel. LS-325 at 16 µm and oil absorption 40 is the slip grade…
146LS-2500 and LS-6008 are both listed at 8 µm but with different oil absorption. Which number do I trust?The oil absorption figure — the size is a nominal mean, and the two grades are produced on different lines. LS-2500 reports 8 µm with surface area 8 and oil absorption 81; LS-6008 reports 8 µm with su…
147Is your talc asbestos-free, and how is that documented?Yes. Every lot is tested for asbestos and the result is reported on the COA, which is the document a customer questionnaire is actually asking for. The test is by a recognised method on the incoming o…
148What are the current regulatory pressures on talc, and how should I plan?The direction is toward tighter documentation and, in some markets, restricted use in specific product types. The practical response is to keep a documented substitution path rather than to wait. Two …
149What is the BVL series, and do I need it?It is the same talc held to the German BVL heavy-metal limits, which are stricter than the general cosmetic specification and are used as a reference by a number of European customers. You need it if …
150What loading do you see in loose powder versus pressed powder?Loose powder 40–70%, pressed powder 25–45%. Talc is usually the base, not an additive. In loose powder the ceiling is feel: past about 70% the powder starts to fly and the pay-off becomes uneven. In p…
151How do I keep talc from flying during filling?Reduce the fine fraction and control humidity, in that order. Airborne dust during filling is mostly the sub-10 µm fraction, and a coarse grade such as LS-325 generates noticeably less of it than a 5 …
152Can I replace talc completely?In most formulas, yes, but it takes more than one material. Talc does three jobs at once — slip, oil absorption and cost — and no single substitute does all three at the same price. The usual approach…
153Does particle size affect adhesion and wear?It affects them through the oil absorption path more than directly. Finer talc with higher oil absorption takes up more of the binder and the sebum, which can improve wear because the film stays drier…
154What is the MOQ, and can you ship in a specific packaging?MOQ is 25 kg for a stock grade, 100–200 kg for a non-stock grade. Lead time 7–15 working days, samples 1 kg. Standard packing is 25 kg paper-plastic composite bags; 500 kg and 1000 kg jumbo bags are a…
155If I cut the talc in a loose powder by half, what has to change to keep the same feel?Four things, and skipping any one of them is why talc reduction usually fails on the first trial. Slip has to be replaced, not just the volume. Talc's glide comes from its platy structure, so the dire…
156Can talc be used in eye products, and what are the limits?It is permitted in eye products in most markets, and traditionally pressed eyeshadow was built on it. The limits are practical rather than categorical. The first is dust. Eye products are applied clos…
157Does talc cake up once it absorbs oil?Talc absorbs comparatively little oil and absorbs it slowly, so it is one of the less caking materials in a powder — that is part of why it was the default for so long. What caking it does show usuall…

Wet Ground Mica13 answers

158Natural mica or synthetic fluorphlogopite?Natural for cost and for a slightly more 'real' lustre; synthetic for purity, whiteness and a cleaner regulatory story. Wet-ground natural mica carries the natural trace elements of the mineral, which…
159Where does sericite fit, and why is it priced differently from mica?Sericite is a fine-grained muscovite with a smaller platelet and a more matte appearance. It is the grade you use when you want the platy structure of mica without the sparkle. The difference is optic…
160How does particle size change the look?Coarser platelets give more sparkle and more visible shimmer; finer ones give a softer sheen and more coverage. On a 6 to 20 µm ladder, 20 µm (Kingcovite 71) gives the most pronounced pearlescent effe…
161Can mica carry a pressed powder on its own if I remove the talc?It can carry the structure, but not the oil control. Mica is platy like talc and presses well, and its lower bulk density means you use less by weight for the same volume. What it does not do is absor…
162Why is synthetic fluorphlogopite whiter than natural mica?Because it is grown from a controlled melt rather than mined, so it has none of the iron and other trace colourants that tint a natural mineral. Natural mica's colour varies by ore body, which is why …
163Is there a BVL grade in the mica range?Yes — Kingcovite 6710 at 10 µm, held to the German BVL heavy-metal limits. It sits in the synthetic fluorphlogopite group, which is where the strictest market requirements usually land, because the sy…
164What loading should I use in eyeshadow and in face powder?Eyeshadow 20–50%, face powder 5–25%. In eyeshadow, mica is often the structural base — it provides the press strength, the pay-off and the pearl, and the pigment sits on top of it. Below 20% the shado…
165Why do my pressed eyeshadows show streaks or a directional sheen?Because the platelets align during pressing, and the alignment is not uniform. Platy materials orient parallel to the pressing surface, which is what produces the sheen — but if the fill is uneven or …
166What is the MOQ and what packing do you use?25 kg per bag, 500 kg jumbo bags available. MOQ 25 kg for stock grades, 100–200 kg for non-stock. Lead time is about 7–15 working days; samples are 1 kg and ship with COA and TDS. Mica is a low-bulk-d…
167Wet-ground or dry-ground mica — what changes in the formula?Wet grinding delaminates the platelets in a liquid medium, so you get thinner, wider, more intact sheets with a narrow size distribution. Dry grinding fractures them, which produces a broader spread a…
168Where does mica's pearlescence come from, and how is it different from a pearlescent pigment?The two are different effects, even though both get called pearl. Mica's own sheen is geometric. Flat transparent platelets align parallel to the surface and reflect light specularly off many layers a…
169Why does mica feel so good on skin?Because it is flat, and flat things lie down. The platelets are thin relative to their width, so they settle parallel to the skin instead of standing on edge, and the surface your finger meets is a sm…
170Can mica be used in liquid foundations and cushions?Yes, and it is common in both, but the behaviour is different from a powder. In a fluid the platelets settle and orient horizontally during storage, so the product can develop a soft sediment and, on …

Colour & Dispersion

CI numbers, lake selection, pre-dispersed slurries and colour-change systems.

Cosmetic Pigments11 answers

171Inorganic pigment or organic lake — how do I decide?By the shade you need and by the regulatory route you can accept, not by preference. Inorganic pigments (iron oxides, ultramarine, chromium oxide) are mineral, opaque, light-stable and cheap per unit …
172How does the CI number work, and why does it matter for my registration?The CI number is the Colour Index identifier for the colorant itself, independent of who makes it or what it is called commercially. Regulators list colorants by CI number. That means your registratio…
173Ultramarine is marked as unstable under acidic conditions. How acidic is a problem?Below roughly pH 5 it starts to decompose, releasing hydrogen sulphide; the change is visible as a loss of blue and a smell. That matters in three places: an AHA or BHA product, a low-pH gel, and any …
174Your iron oxides come in needle, spherical and rhombus shapes. Does shape matter?It changes packing, coverage and how the pigment disperses — and in a pressed product, it changes the press behaviour too. 340Y yellow and 116R red are needle-shaped, which gives good colour strength …
175Is carmine permitted everywhere, and what do I need to declare?It is permitted in most markets but with different conditions, and in some customer specifications it is excluded outright regardless of law. Carmine (CI 75470) is a natural colorant derived from coch…
176You list two carbon black grades with different compliance statements. What is the difference?They are the same pigment held to two different market specifications, which is a documentation difference, not a performance one. 980B FDA is released against US requirements; 970B is released agains…
177Which lakes can I use in lip products?Check the market's permitted list by CI number and by product category — that is the only reliable test, because the answer differs between the EU, the US and China for the same lake. As a starting po…
178How do I compare light fastness between two grades?Test them in your own base under your own conditions — a light fastness rating on a datasheet is a starting filter, not a result. The published ratings in our water-soluble dye series (the star rating…
179Why does my shade look weaker after switching to a lake?Because lakes are dyes on a substrate, so a kilo of lake contains less actual colour than a kilo of pigment. The substrate — usually alumina or a rosin — is part of the weight. That is why the loading…
180What are the MOQ and lead time for pigments?MOQ is 1 kg for a stock grade and 25 kg for a production quantity; some specialty lakes have a 5 kg minimum because they are made to order. Lead time is 7–15 working days, longer for a non-stock lake.…
181My pressed powder looks weak in colour. Is it the pigment or the base?Usually the base — and you can tell in one test, by pressing the same pigment load in a base with and without the opacifying filler. Three base effects flatten colour in a compact. A high whitening fi…

Pigment Formulation9 answers

182Ultramarine in an acidic formula — is pH control enough?Sometimes, but if the product has to be acidic, ultramarine is the wrong blue. Ultramarine (CI 77007) is acid-sensitive and can decompose with release of hydrogen sulphide, which shows up as odour and…
183What does a lip pigment have to satisfy beyond the CI list?Three things on top of permitted use: migration resistance, odour, and the narrower lip list itself. Permitted use is the gate. Lip products are partly ingested, and every market runs a shorter list f…
184Can a UV absorber rescue a pigment with poor light fastness?It delays the fade; it does not fix it. If light fastness is the weakness, treat it as a selection criterion rather than something to patch later. Assess first. Draw the pigment down in the target bas…
185How much pigment is enough for colour, and what goes wrong at high loading?There is no general number — it depends on the pigment's strength, the base colour and the target depth. Typically 0.5–10%, higher for deep shades. Strength varies widely. Organic lakes are strong, so…
186Speckles and uneven colour — wetting, dispersion or stabilization?Usually all three, in that order. Work through them in sequence instead of adding dispersant and hoping. Wetting comes first. Pigment has a large surface area and adsorbs air, so tipping it dry into a…
187Is pigment surface treatment mandatory in a silicone system?Not by rule, but in a silicone system carrying a water-resistance or long-wear claim it is close to unavoidable. The treated grades on our list carry the same pigment with different layers: SI for sli…
188Which compliance documents should travel with a colourant?Four groups: CI number and permitted-use statement, heavy-metal report, microbiological report, and whatever the target market adds on top. The CI statement is the core document. It has to name the CI…
189Why does colour rub off a pressed powder?It is adhesion and compatibility, not a pigment that is inherently loose. Three causes. The pigment does not bond to the platelet fillers — talc, mica — so it sits at the surface and wipes away. The f…
190Batch-to-batch colour drift — what can the formula actually do?Fix the grade, control incoming batches, and build a little tolerance into pale shades. The formula cannot eliminate it. Pigments are mineral or synthetic and natural variation exists — inorganics esp…

Oil-based Slurry14 answers

191Should I use a pre-dispersed slurry or mill the pigment myself?Slurry if you are under roughly 200 kg per batch or you do not have a bead mill; dry pigment if you are large enough to amortise the equipment and the cleaning. The slurry saves you the milling step, …
192Your slurries run from 40% to 73% pigment content. How do I choose?Choose by the pigment, not by a preference for higher concentration. High loadings are achievable with dense, well-behaved pigments: TiO2 at 73% (867W), black iron oxide at 70% (926B), and the treated…
193What does the DSG treatment do in a slurry?It makes the pigment surface lipophilic so the dispersion stays stable in the oil phase and the film wears longer. DSG — disodium stearoyl glutamate — is a surface treatment applied to the pigment bef…
194What is the AMQ series for long-wearing foundation?It is a set of four dispersions built for transfer-resistant foundations, where the film has to stay put on oily skin for a full day. The four grades are TiO2 (869W, 60%), red iron oxide (116R, 55%), …
195The carrier is isononyl isononanoate. Can I have a different one?Yes, for a production quantity. The standard carrier is chosen because it is a good general-purpose emollient with a dry feel and wide compatibility. Common alternatives are caprylic/capric triglyceri…
196How is a slurry declared for regulatory purposes?As the pigment plus the carrier plus the treatment, which means the CI number alone is not the whole declaration. On an INCI list, the dispersion appears as the pigment's CI number together with the c…
197Why does the slurry settle, and how do I redisperse it?Settling is normal for a high-loading dispersion; hard caking is not, and the difference is usually storage temperature and time. A soft sediment that redisperses with a paddle is expected and harmles…
198What is the MOQ and the shelf life?MOQ is 5 kg for a stock grade and 25 kg for a production quantity; a custom carrier is 100–200 kg. Shelf life is typically 24 months from production in an unopened container. Lead time is 7–15 working…
199Can I use an oil-based slurry in a lipstick?Yes, and it is a sensible route, because a lipstick is an anhydrous system and the standard carriers — isononyl isononanoate, C12-15 alkyl benzoate — are already typical lipstick emollients. Three thi…
200I am switching from dry pigment to slurry. What has to change in the formula?Three things, and the first one catches most people. The carrier becomes an ingredient. A 60% slurry added at 10% puts 4% of carrier into the formula, and that carrier is an emollient your oil phase n…
201How do I convert pigment content in a slurry into a formula percentage?Divide the pigment percentage you want by the slurry's pigment content. If the formula calls for 8% TiO2 and you are using an 867W slurry at 73%, you need 8 ÷ 0.73 = 11.0% of slurry. That 11.0% delive…
202AS or DSG treatment — what is the difference in a slurry?Both are surface treatments that make the pigment lipophilic, and both improve dispersion and wear. The practical difference is hand feel and the chemistry they suit. DSG — disodium stearoyl glutamate…
203Can a slurry be used in a pressed powder?Not normally, and it is worth understanding why rather than testing it. A pressed powder is a dry blend held together by a small amount of binder, and the balance between powder surface and binder is …
204A batch came out off-shade. Is it the slurry or my formula?Check in this order: the container, the batch record, then the formula. First the container. A high-loading slurry separates, and the top layer is carrier-rich while the bottom is pigment-rich. If the…

Water-based Slurry14 answers

205Oil-based or water-based slurry — what decides it?The continuous phase of your finished emulsion, and nothing else. Put a water-based slurry into an anhydrous base and it will not incorporate; put an oil-based one into a gel and the same thing happen…
206Why is the pigment content lower in water-based slurries?Because water has a lower viscosity at the same solids and cannot hold a dense pigment load in suspension without settling or gelling. The numbers show it: TiO2 in water reaches 60–65% (848W, 851W) be…
207What is the difference between transparent and regular iron oxide?Particle size. Transparent grades are far finer, so they absorb colour but scatter much less light — they tint without hiding. Regular iron oxide at a few hundred nanometres gives opacity and coverage…
208How do I stop the slurry from settling in storage?Accept soft settling, prevent hard caking, and mix before use. A water-based dispersion with a high pigment load will settle; what you control is whether it settles into a soft sediment or a hard cake…
209What is the graphene dispersion, and what is it used for?It is an aqueous graphene dispersion positioned as a black colourant alternative, not as an additive for conductivity or strength. The datasheet lists its use as a replacement for bamboo charcoal, car…
210What about preservation in a water-based slurry?The slurry is preserved as supplied, but the preservation margin in your finished product is yours to establish. A water-based dispersion is an aqueous system with a carbon source in it, so microbial …
211What are the eyeliner and nail polish series?They are the same dispersion technology tuned for two applications with unusual demands. The high-waterproof eyeliner series is built for films that stay on a wet lash line without smearing, so the di…
212What is the MOQ and lead time?MOQ is 5 kg for a stock grade and 25 kg for production. Lead time 7–15 working days, samples 1 kg. Shelf life is typically 12 months for water-based products, shorter than the oil-based range because …
213How do I add a water-based slurry to a cushion or a liquid foundation?Add it to the water phase before emulsification, not to the finished emulsion. The pigment needs to be fully wetted by the aqueous phase. Adding it after the emulsion is formed means it has to find it…
214The slurry separates or floats in my formula. What causes it?Two different problems look the same from the outside, and they have different fixes. Flotation is pigment migrating upward as a separate layer, usually because it has flocculated into clusters that a…
215Is a water-based slurry the same as a pigment dispersion?In practice the terms overlap and suppliers use them loosely, so the only reliable approach is to ask what is in the container. A slurry, in our sense, is pigment dispersed in a carrier with a dispers…
216How is fineness controlled, and what happens if the dispersion is too coarse?Fineness is set at the milling stage and verified on a grind gauge — a drawdown on a graduated steel block that shows the largest remaining agglomerates in microns. If a dispersion is too coarse, four…
217Can water-based slurries be used in skincare with colour?Yes, and it is a growing category, but the compliance route is different from a decorative product. A tinted moisturiser or a coloured serum is still a cosmetic, so the colourant has to be permitted f…
218What regulatory points apply to yellow, red and blue water-based slurries?The colour drives the regulation, not the carrier — and yellow, red and blue each sit in a different place. Yellows are usually iron oxide, which is widely permitted, or an organic lake, which is rest…

Allochroic Particles11 answers

219How do these particles change colour — pH, or temperature?They are encapsulation-based colour-change systems. The colour shift is triggered by the aqueous environment around the particle, which in a cosmetic product means pH and moisture rather than temperat…
220What is the difference between the 460 and 160 series?460 is the universal grade and 160 is specified for W/O emulsions. The 460 series (WY-460, WR-460, WB-460, BS-460, WG-460, WV-460) covers six colour shifts including white-to-skin-tone, and is used ac…
221Why does the colour not shift in my formula?Usually because the particle is fully wetted and stays wetted, so there is no change in its local environment to trigger the shift. The effect depends on the particle experiencing a change — typically…
222What loading do you recommend?1–5%, with the effect becoming obvious around 2–3%. Below 1% the shifted colour is too diffuse to read as a deliberate effect, and it looks like an off-shade rather than a colour change. Above 5% the …
223How stable are they over shelf life?Stable in a properly formulated base, but they are the most process-sensitive material in our range — handle them accordingly. The shell is the functional part, so anything that damages it also kills …
224How are colour-change products regulated?As cosmetics containing colourants, which means the colourant inside the particle has to be permitted for the product category in the destination market — the encapsulation does not exempt it. In prac…
225Is the change reversible?In use, the shift is intended to be a one-way visual effect within the application — the product changes as it is applied and does not return to the original colour on the skin. That is the point of t…
226What is the MOQ and how should it be stored?MOQ is 1 kg for a sample and 25 kg for production. Lead time 7–15 working days. Store sealed, at 15–30 °C, away from direct light and away from strong odours — the shell can pick up volatile compounds…
227Do colour-change particles work in a dry powder format?With difficulty, and usually not for the reason people expect. The shift needs a change in the particle's local environment, and a dry powder does not provide one — there is no water to trigger it dur…
228Does the particle size of a colour-change pigment change how it feels on skin?Yes, and it is a tighter constraint than with a conventional pigment, because the particle is an encapsulated shell and the shell has a physical size. These particles are typically in the tens of micr…
229Can I blend allochroic particles with regular pigments?Yes, and most commercial colour-change products do, because the particles alone give an effect rather than a usable shade. Two things to watch. Opacity: a high-coverage pigment will mask the shift, so…

Functional & Processing

Surface treatments, inorganic UV filters and custom grades.

Surface Treatment13 answers

230When is a surface treatment worth paying for?When the powder has to survive a system it was not born to live in — a silicone phase, a W/O emulsion, a high-humidity wear claim, or a compact that has to press hard. Untreated mineral powder is hydr…
231There are eleven treatment types. How do I narrow it down?By what you are trying to fix — that is what separates them. Dimethicone (SI) is the general-purpose choice: chemically bonded, shear-resistant, works over a wide temperature range, gives strong water…
232Can the SI treatment be applied to any grade?Yes — to all series and particle sizes. That is stated on the page and it is the practical advantage of the range. So Kingbornit 3002 SI, Kingsica 3028 SI, Kingruti 0205 SI, Kingtalfer LS-800 SI and K…
233Does a surface treatment change the colour or the coverage?Very little, and what does change is the dispersion, which can look like a colour change until you know why. The treatment is a molecular layer on the surface, so it does not alter the refractive inde…
234What is the difference between triethoxycaprylylsilane and dimethicone treatment?Both make the surface hydrophobic; the silane does it without adding a silicone feel, which is why it dominates in UV filters. Triethoxycaprylylsilane bonds directly to the surface hydroxyls and gives…
235How do I verify that the treatment is actually there?Three quick checks, in increasing order of effort. First, the water float test: a treated powder floats on water and an untreated one wets and sinks. It is crude but it tells you immediately whether t…
236Does treating a powder affect its regulatory status?Yes, in the sense that the treatment agent becomes part of the ingredient declaration and must itself be permitted. A treated powder is not the same regulatory object as the untreated one: the coating…
237Do I need to change the loading when I switch to a treated grade?Usually not — start at the same loading and adjust on the result. The treatment is a small weight percentage on the surface, so the delivered pigment or powder content per kilo is essentially unchange…
238What loading of treated powder do you see in a W/Si system?It depends on the powder, but the treated grades are what make high loadings possible in silicone-continuous systems. In a W/Si foundation, treated TiO2 and treated iron oxides commonly run at 8–15% c…
239Is there a treatment for a hydrophilic system?Yes — the hydrophilic treatment exists for water-based and O/W systems where you want improved dispersion without making the surface hydrophobic. It is the counterpart to the lipophilic treatments: in…
240What is the MOQ for a treated grade?25 kg for a stock treated grade; a treatment applied to a grade we do not normally carry is 100–200 kg, because the treatment line has to be set up and cleaned. Lead time is 7–15 working days for stoc…
241What dosage of treatment agent is used, and what happens if it is too low?Treatments are applied at roughly 1–3% on the weight of the powder, depending on the agent and the surface area of the grade. A finer powder needs more, because there is more surface to cover. Too low…
242I changed treatment supplier on the same base powder. What has to be re-qualified?Treat it as a new raw material, not as a purchasing change. The base powder is the same; the surface chemistry is not, and the surface is what your formula interacts with. Re-qualify in this order. Di…

Surface Treatment Application 10 answers

243Treatment dosage scales with surface area. How do I set it for a new grade?There is no universal figure. Dosage is set per powder, from its specific surface area and from what you want the treatment to do. The rule is straightforward: the higher the specific surface area, th…
244How far does oil absorption drop after treatment — and when is that a problem?Usually a clear drop, and the size of it depends on agent type and coverage. For most formulas that drop is the main reason to pay for treatment. The mechanism: the agent occupies active sites on the …
245Does treatment change SPF enough that I have to re-test?Yes, and the direction depends on the agent and the loading. It cannot be assumed either way — it has to be measured. Two mechanisms act at once. Better dispersion means the particles sit more evenly …
246Will a treatment shift the shade enough to need re-matching?Slightly, and mostly through gloss, transparency and saturation rather than hue. Pale and bright shades are the sensitive ones. The layer changes refractive index and scattering at the surface, so wha…
247Which processes break down a treatment layer?Three-roll milling, bead milling, high-shear homogenising, and long hot emulsification. All four apply shear and heat together, which is what a treatment layer tolerates least. When the layer fails yo…
248Can I claim silicone-free when the powder is SI-treated?No — not if the treatment is a silicone. This is the most common place a "silicone-free" claim fails. "SI" is a family label, not an ingredient. The agent may be dimethicone, a polymethylsiloxane or a…
249Switching from one treatment type to another — what is the full re-test list?Six items minimum: dispersion, viscosity, stability, skin feel, colour where a pigment is involved, and whatever functional claim the product makes. Dispersion and viscosity move first, because the ag…
250Can treatment stop a heavy powder from settling?It helps, but it cannot change the physics. Settling is a density and particle-size problem; treatment only changes surface compatibility. What treatment does: better compatibility with the continuous…
251Does treatment raise tinting strength? Do I have to cut the loading?Yes, usually — and yes, expect to cut the loading when you move from an untreated to a treated pigment. The gain is a dispersion effect, not a stronger pigment. Fewer agglomerates mean more effective …
252How do I prove a treatment is working, layer by layer?Four layers, in this order: surface properties, dispersion state, formula performance, then stability. Skipping to the last one is why treatments get blamed for problems they did not cause. Surface fi…

Inorganic Sunscreen13 answers

253Nano TiO2 or nano ZnO — which should I use?ZnO for UVA coverage and TiO2 for UVB and the higher refractive efficiency; many serious formulas use both. ZnO has a wider absorption band that extends further into UVA, which is why it appears in pr…
254Nano or non-nano? What is the regulatory difference?It is the single most consequential decision in an inorganic sunscreen, because nano status changes the notification route, the labelling and the safety dossier. Most markets define nano by primary pa…
255Your grades run from 15 nm to 160 nm. What does size change?Smaller particles give more transparency and better SPF per unit mass; larger ones give less whitening but require more loading, and above a certain size the UV performance starts to drop. 15 nm (N15E…
256Powder or pre-dispersion?Pre-dispersion if you can — it solves the hardest problem in the formula, which is wetting a nano powder completely. Nano powders have enormous surface area and agglomerate readily; getting them fully…
257How do I choose the carrier for a pre-dispersion?Match it to your emollient system and to the feel you want — the carrier becomes part of the formula. C12-15 alkyl benzoate (4015, 4513, 4560, Z-6060) is the general-purpose choice: light, dry, widely…
258How much do I need to reach a given SPF?As a rough starting point, 5–10% combined inorganic solids gets you into the moderate-SPF range, and 15–25% is where mineral-only high-SPF formulas live — but the number that matters is measured in yo…
259Does the coating matter for photostability?Yes — it is the main lever you have over the photocatalytic activity of the particle. TiO2 and ZnO generate reactive species at the surface when they absorb UV, and those species attack the surroundin…
260How do I reduce the white cast?Smaller particle size, better dispersion, and if necessary a lower loading with an organic filter carrying the rest of the SPF. White cast has two causes. Undispersed agglomerates scatter visible ligh…
261What testing documents do you provide?We provide the material documentation: COA, TDS, SDS, and the nano-specific statements a market may require. The finished-product testing — SPF, UVA-PF, critical wavelength, water resistance — is done…
262What are the MOQ and lead time for sunscreen grades?MOQ is 1 kg for a powder sample and 5 kg for a pre-dispersion sample; production quantities start at 25 kg. Lead time is 7–15 working days for stock grades, longer for a custom carrier. Because nano m…
263Why does my mineral sunscreen pill or roll up?Pilling is a film problem, not a pigment problem, and it usually has one of three causes. The first is an incompatibility between the sunscreen film and the product applied underneath. A mineral sunsc…
264Can a mineral sunscreen be made as a spray?Yes, but only as a pump spray, and the formulation window is narrow. A pressurised aerosol with mineral filters is a problem on two counts: the powder settles in the propellant system, and the inhalab…
265Can bismuth oxychloride be used as a UV filter?No. In cosmetic formulas bismuth oxychloride (CI 77163, Kingbismo® range) works as a pearlescent and soft-focus colorant: its plate-like crystals reflect visible light to give a satin lustre, but they…

Sunscreen Formulation8 answers

266White cast and grey cast are not the same problem — how do I tell them apart?White cast is scattering; grey cast is usually hue. They take different fixes, so diagnose before reformulating. White cast comes from visible-light scattering by particles whose size is comparable to…
267Pilling gets worse when I layer foundation over sunscreen — whose problem is it?Usually the interface, not either product on its own. A mineral sunscreen built on a W/O emulsion leaves a film that a water-based foundation then sits on. The two films shear against each other as th…
268SPF does not scale with filter loading — where is the knee?It rises, then flattens, and past the knee it can fall. Do not size the loading from a linear calculation. More filter means more shielding per unit area, so SPF climbs. Then the marginal return drops…
269The carrier counts as oil in my formula — how much do I subtract?All of it, by mass. A pre-dispersion is a raw material that brings oil with it, and that oil is in the formula whether or not it was counted. Our dispersions come in several carriers: C12-15 alkyl ben…
270How do I test whether a mineral sunscreen will oxidise in the bottle?Accelerated light exposure plus peroxide value. The coating specification tells you the risk; the test tells you the outcome. The mechanism: nano TiO2 and ZnO generate electron-hole pairs under UV, wh…
271A mineral sunscreen feels heavy and suffocating — where do I start?Powder form, oil structure, film former — in that order. Cutting the filter load is the last resort, because it costs protection. Powder first. A pre-dispersion spreads more evenly than powder dispers…
272Do pre-dispersions settle, and how do I keep batches consistent?They settle, because the particles are denser than the carrier. That is physics; the job is to keep it redispersible and to dose by solids. How fast depends on three things: particle size, since agglo…
273What does a nano spray sunscreen need before it can be notified?The inhalation route is the whole question, and it has to be settled before the formula is developed, not before launch. A spray creates an inhalable aerosol. Nano TiO2 or ZnO reaching the lung is a d…

Others6 answers

274Can you make a custom grade — a size or treatment you do not list?Yes, within the limits of the production line. Particle size classification and surface treatment are both adjustable, and a custom combination is a normal request rather than an exception. What is re…
275What does the sample programme include?1 kg of powder or 5 kg of a dispersion, with COA, TDS and SDS. Samples are free; you cover the freight. For a first evaluation, ask for two grades rather than one — the comparison is what tells you wh…
276What documents come with a shipment?COA per lot, TDS per grade, and SDS. Beyond that, the regulatory statements a market requires — heavy metal declarations, non-nano or nano statements, allergen declarations, REACH status, BSE/TSE stat…
277What are the general order terms?MOQ 25 kg for a stock grade, 100–200 kg for a custom grade or a custom carrier. Lead time 7–15 working days for stock, longer for custom. Payment terms are confirmed at quotation and depend on the mar…
278Can you help with the formulation, not just the material?Yes, within limits — we can tell you what has worked in comparable systems and what the common failure modes are, and we can review a formula for obvious incompatibilities. What we cannot do is take r…
279Which grades are outside these twelve categories?This page is the catch-all for materials that do not sit cleanly in one of the other product families — specialty fillers, materials in development, and combinations that are made to order. If you can…
No answer matches your search. Try pilling, D50, talc or MOQ.
Not finding an answer?

Describe your formulation system and the problem — the technical team replies within one business day, and can arrange samples at the same time.

Talk to our technical team
Become a Distributor