Colour & Dispersion FAQ
CI numbers, lake selection, pre-dispersed slurries and colour-change systems.
Colour & Dispersion59 answers
Cosmetic Pigments11 answers
001Inorganic pigment or organic lake — how do I decide?By the shade you need and by the regulatory route you can accept, not by preference. Inorganic pigments (iron oxides, ultramarine, chromium oxide) are mineral, opaque, light-stable and cheap per unit …
002How does the CI number work, and why does it matter for my registration?The CI number is the Colour Index identifier for the colorant itself, independent of who makes it or what it is called commercially. Regulators list colorants by CI number. That means your registratio…
003Ultramarine is marked as unstable under acidic conditions. How acidic is a problem?Below roughly pH 5 it starts to decompose, releasing hydrogen sulphide; the change is visible as a loss of blue and a smell. That matters in three places: an AHA or BHA product, a low-pH gel, and any …
004Your iron oxides come in needle, spherical and rhombus shapes. Does shape matter?It changes packing, coverage and how the pigment disperses — and in a pressed product, it changes the press behaviour too. 340Y yellow and 116R red are needle-shaped, which gives good colour strength …
005Is carmine permitted everywhere, and what do I need to declare?It is permitted in most markets but with different conditions, and in some customer specifications it is excluded outright regardless of law. Carmine (CI 75470) is a natural colorant derived from coch…
006You list two carbon black grades with different compliance statements. What is the difference?They are the same pigment held to two different market specifications, which is a documentation difference, not a performance one. 980B FDA is released against US requirements; 970B is released agains…
007Which lakes can I use in lip products?Check the market's permitted list by CI number and by product category — that is the only reliable test, because the answer differs between the EU, the US and China for the same lake. As a starting po…
008How do I compare light fastness between two grades?Test them in your own base under your own conditions — a light fastness rating on a datasheet is a starting filter, not a result. The published ratings in our water-soluble dye series (the star rating…
009Why does my shade look weaker after switching to a lake?Because lakes are dyes on a substrate, so a kilo of lake contains less actual colour than a kilo of pigment. The substrate — usually alumina or a rosin — is part of the weight. That is why the loading…
010What are the MOQ and lead time for pigments?MOQ is 1 kg for a stock grade and 25 kg for a production quantity; some specialty lakes have a 5 kg minimum because they are made to order. Lead time is 7–15 working days, longer for a non-stock lake.…
011My pressed powder looks weak in colour. Is it the pigment or the base?Usually the base — and you can tell in one test, by pressing the same pigment load in a base with and without the opacifying filler. Three base effects flatten colour in a compact. A high whitening fi…
Pigment Formulation9 answers
012Ultramarine in an acidic formula — is pH control enough?Sometimes, but if the product has to be acidic, ultramarine is the wrong blue. Ultramarine (CI 77007) is acid-sensitive and can decompose with release of hydrogen sulphide, which shows up as odour and…
013What does a lip pigment have to satisfy beyond the CI list?Three things on top of permitted use: migration resistance, odour, and the narrower lip list itself. Permitted use is the gate. Lip products are partly ingested, and every market runs a shorter list f…
014Can a UV absorber rescue a pigment with poor light fastness?It delays the fade; it does not fix it. If light fastness is the weakness, treat it as a selection criterion rather than something to patch later. Assess first. Draw the pigment down in the target bas…
015How much pigment is enough for colour, and what goes wrong at high loading?There is no general number — it depends on the pigment's strength, the base colour and the target depth. Typically 0.5–10%, higher for deep shades. Strength varies widely. Organic lakes are strong, so…
016Speckles and uneven colour — wetting, dispersion or stabilization?Usually all three, in that order. Work through them in sequence instead of adding dispersant and hoping. Wetting comes first. Pigment has a large surface area and adsorbs air, so tipping it dry into a…
017Is pigment surface treatment mandatory in a silicone system?Not by rule, but in a silicone system carrying a water-resistance or long-wear claim it is close to unavoidable. The treated grades on our list carry the same pigment with different layers: SI for sli…
018Which compliance documents should travel with a colourant?Four groups: CI number and permitted-use statement, heavy-metal report, microbiological report, and whatever the target market adds on top. The CI statement is the core document. It has to name the CI…
019Why does colour rub off a pressed powder?It is adhesion and compatibility, not a pigment that is inherently loose. Three causes. The pigment does not bond to the platelet fillers — talc, mica — so it sits at the surface and wipes away. The f…
020Batch-to-batch colour drift — what can the formula actually do?Fix the grade, control incoming batches, and build a little tolerance into pale shades. The formula cannot eliminate it. Pigments are mineral or synthetic and natural variation exists — inorganics esp…
Oil-based Slurry14 answers
021Should I use a pre-dispersed slurry or mill the pigment myself?Slurry if you are under roughly 200 kg per batch or you do not have a bead mill; dry pigment if you are large enough to amortise the equipment and the cleaning. The slurry saves you the milling step, …
022Your slurries run from 40% to 73% pigment content. How do I choose?Choose by the pigment, not by a preference for higher concentration. High loadings are achievable with dense, well-behaved pigments: TiO2 at 73% (867W), black iron oxide at 70% (926B), and the treated…
023What does the DSG treatment do in a slurry?It makes the pigment surface lipophilic so the dispersion stays stable in the oil phase and the film wears longer. DSG — disodium stearoyl glutamate — is a surface treatment applied to the pigment bef…
024What is the AMQ series for long-wearing foundation?It is a set of four dispersions built for transfer-resistant foundations, where the film has to stay put on oily skin for a full day. The four grades are TiO2 (869W, 60%), red iron oxide (116R, 55%), …
025The carrier is isononyl isononanoate. Can I have a different one?Yes, for a production quantity. The standard carrier is chosen because it is a good general-purpose emollient with a dry feel and wide compatibility. Common alternatives are caprylic/capric triglyceri…
026How is a slurry declared for regulatory purposes?As the pigment plus the carrier plus the treatment, which means the CI number alone is not the whole declaration. On an INCI list, the dispersion appears as the pigment's CI number together with the c…
027Why does the slurry settle, and how do I redisperse it?Settling is normal for a high-loading dispersion; hard caking is not, and the difference is usually storage temperature and time. A soft sediment that redisperses with a paddle is expected and harmles…
028What is the MOQ and the shelf life?MOQ is 5 kg for a stock grade and 25 kg for a production quantity; a custom carrier is 100–200 kg. Shelf life is typically 24 months from production in an unopened container. Lead time is 7–15 working…
029Can I use an oil-based slurry in a lipstick?Yes, and it is a sensible route, because a lipstick is an anhydrous system and the standard carriers — isononyl isononanoate, C12-15 alkyl benzoate — are already typical lipstick emollients. Three thi…
030I am switching from dry pigment to slurry. What has to change in the formula?Three things, and the first one catches most people. The carrier becomes an ingredient. A 60% slurry added at 10% puts 4% of carrier into the formula, and that carrier is an emollient your oil phase n…
031How do I convert pigment content in a slurry into a formula percentage?Divide the pigment percentage you want by the slurry's pigment content. If the formula calls for 8% TiO2 and you are using an 867W slurry at 73%, you need 8 ÷ 0.73 = 11.0% of slurry. That 11.0% delive…
032AS or DSG treatment — what is the difference in a slurry?Both are surface treatments that make the pigment lipophilic, and both improve dispersion and wear. The practical difference is hand feel and the chemistry they suit. DSG — disodium stearoyl glutamate…
033Can a slurry be used in a pressed powder?Not normally, and it is worth understanding why rather than testing it. A pressed powder is a dry blend held together by a small amount of binder, and the balance between powder surface and binder is …
034A batch came out off-shade. Is it the slurry or my formula?Check in this order: the container, the batch record, then the formula. First the container. A high-loading slurry separates, and the top layer is carrier-rich while the bottom is pigment-rich. If the…
Water-based Slurry14 answers
035Oil-based or water-based slurry — what decides it?The continuous phase of your finished emulsion, and nothing else. Put a water-based slurry into an anhydrous base and it will not incorporate; put an oil-based one into a gel and the same thing happen…
036Why is the pigment content lower in water-based slurries?Because water has a lower viscosity at the same solids and cannot hold a dense pigment load in suspension without settling or gelling. The numbers show it: TiO2 in water reaches 60–65% (848W, 851W) be…
037What is the difference between transparent and regular iron oxide?Particle size. Transparent grades are far finer, so they absorb colour but scatter much less light — they tint without hiding. Regular iron oxide at a few hundred nanometres gives opacity and coverage…
038How do I stop the slurry from settling in storage?Accept soft settling, prevent hard caking, and mix before use. A water-based dispersion with a high pigment load will settle; what you control is whether it settles into a soft sediment or a hard cake…
039What is the graphene dispersion, and what is it used for?It is an aqueous graphene dispersion positioned as a black colourant alternative, not as an additive for conductivity or strength. The datasheet lists its use as a replacement for bamboo charcoal, car…
040What about preservation in a water-based slurry?The slurry is preserved as supplied, but the preservation margin in your finished product is yours to establish. A water-based dispersion is an aqueous system with a carbon source in it, so microbial …
041What are the eyeliner and nail polish series?They are the same dispersion technology tuned for two applications with unusual demands. The high-waterproof eyeliner series is built for films that stay on a wet lash line without smearing, so the di…
042What is the MOQ and lead time?MOQ is 5 kg for a stock grade and 25 kg for production. Lead time 7–15 working days, samples 1 kg. Shelf life is typically 12 months for water-based products, shorter than the oil-based range because …
043How do I add a water-based slurry to a cushion or a liquid foundation?Add it to the water phase before emulsification, not to the finished emulsion. The pigment needs to be fully wetted by the aqueous phase. Adding it after the emulsion is formed means it has to find it…
044The slurry separates or floats in my formula. What causes it?Two different problems look the same from the outside, and they have different fixes. Flotation is pigment migrating upward as a separate layer, usually because it has flocculated into clusters that a…
045Is a water-based slurry the same as a pigment dispersion?In practice the terms overlap and suppliers use them loosely, so the only reliable approach is to ask what is in the container. A slurry, in our sense, is pigment dispersed in a carrier with a dispers…
046How is fineness controlled, and what happens if the dispersion is too coarse?Fineness is set at the milling stage and verified on a grind gauge — a drawdown on a graduated steel block that shows the largest remaining agglomerates in microns. If a dispersion is too coarse, four…
047Can water-based slurries be used in skincare with colour?Yes, and it is a growing category, but the compliance route is different from a decorative product. A tinted moisturiser or a coloured serum is still a cosmetic, so the colourant has to be permitted f…
048What regulatory points apply to yellow, red and blue water-based slurries?The colour drives the regulation, not the carrier — and yellow, red and blue each sit in a different place. Yellows are usually iron oxide, which is widely permitted, or an organic lake, which is rest…
Allochroic Particles11 answers
049How do these particles change colour — pH, or temperature?They are encapsulation-based colour-change systems. The colour shift is triggered by the aqueous environment around the particle, which in a cosmetic product means pH and moisture rather than temperat…
050What is the difference between the 460 and 160 series?460 is the universal grade and 160 is specified for W/O emulsions. The 460 series (WY-460, WR-460, WB-460, BS-460, WG-460, WV-460) covers six colour shifts including white-to-skin-tone, and is used ac…
051Why does the colour not shift in my formula?Usually because the particle is fully wetted and stays wetted, so there is no change in its local environment to trigger the shift. The effect depends on the particle experiencing a change — typically…
052What loading do you recommend?1–5%, with the effect becoming obvious around 2–3%. Below 1% the shifted colour is too diffuse to read as a deliberate effect, and it looks like an off-shade rather than a colour change. Above 5% the …
053How stable are they over shelf life?Stable in a properly formulated base, but they are the most process-sensitive material in our range — handle them accordingly. The shell is the functional part, so anything that damages it also kills …
054How are colour-change products regulated?As cosmetics containing colourants, which means the colourant inside the particle has to be permitted for the product category in the destination market — the encapsulation does not exempt it. In prac…
055Is the change reversible?In use, the shift is intended to be a one-way visual effect within the application — the product changes as it is applied and does not return to the original colour on the skin. That is the point of t…
056What is the MOQ and how should it be stored?MOQ is 1 kg for a sample and 25 kg for production. Lead time 7–15 working days. Store sealed, at 15–30 °C, away from direct light and away from strong odours — the shell can pick up volatile compounds…
057Do colour-change particles work in a dry powder format?With difficulty, and usually not for the reason people expect. The shift needs a change in the particle's local environment, and a dry powder does not provide one — there is no water to trigger it dur…
058Does the particle size of a colour-change pigment change how it feels on skin?Yes, and it is a tighter constraint than with a conventional pigment, because the particle is an encapsulated shell and the shell has a physical size. These particles are typically in the tens of micr…
059Can I blend allochroic particles with regular pigments?Yes, and most commercial colour-change products do, because the particles alone give an effect rather than a usable shade. Two things to watch. Opacity: a high-coverage pigment will mask the shift, so…
No answer matches your search in this topic.
Not finding an answer?
Talk to our technical teamDescribe your formulation system and the problem — the technical team replies within one business day, and can arrange samples at the same time.