Matrix Powders FAQ
Particle size, oil absorption and press behaviour across the mineral fillers.
Matrix Powders79 answers
Wet-Stripped Boron Nitride15 answers
001Which Kingbornit series should I use for Europe, the US and Japan?Start from the market, then pick the particle size. All three series behave the same in the formula — they differ only in how much soluble boron the powder can release. Kingbornit 7000 (7006 / 7012 / …
002How do I choose between the 6, 12, 15 and 20 µm grades?Choose by the skin feel you are targeting, then check the coverage requirement. 6 µm (7006, surface area 9) has the highest surface area in the range and gives the most pronounced soft-focus and cover…
003What loading do you recommend in pressed powder and in loose powder?A common starting point is 3–8%, adjusted upward for skin feel. Loadings above 15% are rare. At low loading boron nitride mainly improves spreading and slip, and contributes little to compact strength…
004Can boron nitride replace talc, and at what ratio?Partly, and not one-for-one. Replacing 20–50% of the talc is usually workable in pressed and loose powders; full replacement is not. The platy structure is similar to talc and slip is typically higher…
005What is soluble borate, and why does the grade matter for export?It is the fraction of boron that can leach out of the powder, and it is what market-specific questionnaires ask about — not the total boron content. Boron nitride itself is chemically inert. Residual …
006The coarser grades have lower specific surface area. Does that change how they behave?Yes, and it is the main reason size selection matters more than series selection. Surface area drives how much binder and oil the powder takes up, and how much light it scatters. Going from 6 µm (area…
007Does boron nitride work in liquids — foundations, creams, lip products?Yes, but for a different reason than in powders. In liquids it is a texture and slip modifier, not a structure former. The plates orient during application and reduce the drag you get from high oil-ab…
008What comes with each lot, and what can you provide for a REACH or customer questionnaire?Every lot ships with a COA reporting the specification figures for that batch, including the soluble boron figure for that grade — quoted as soluble borate % on the 7000 and 3000 series and as boron l…
009What is the minimum order and lead time for a standard grade like 7012?Standard grades are normally stocked and ship in small quantities for sampling; production volumes are quoted per order. Lead time depends on grade and quantity rather than being fixed. In practice: s…
010How does boron nitride affect coverage and whiteness?It does not add coverage, and it is not a whitening filler. Its refractive index is close enough to typical binder and filler systems that it scatters little. What it does is make the finish look soft…
011Boron nitride or a silicone elastomer powder — which gives better slip?They give different kinds of slip, and most premium powders end up using both. Boron nitride is a hard, platy mineral. The glide comes from platelets sliding over each other, and the afterfeel is dry,…
012Do I need the SI-treated boron nitride, and what does the treatment actually solve?The untreated powder is already hydrophobic enough for most anhydrous systems, so the treatment is not about wetting. It is about dispersion stability and film behaviour. The SI grade carries a surfac…
013The boron nitride feels gritty in my formula. What is going wrong?Almost always dispersion, not the grade. The platelets stack face to face and form soft agglomerates that a low-shear mixer will not break, so you feel clusters rather than individual platelets. Two f…
014How do I combine boron nitride with mica and silica?By function, not by ratio. The three do different jobs and substituting one for another is how talc-free projects go wrong. Boron nitride is the lubricant: 2–8% buys glide and pressability. Mica is th…
015Can boron nitride do anything useful in a sunscreen?It is not a UV filter and contributes essentially nothing to SPF. What it does is fix the sensory problems that make people under-apply. At 1–4% in a mineral sunscreen it improves spreadability, reduc…
Spherical Porous Silica14 answers
016How do I choose between oil absorption 60 and 300?By how much oil you need taken out of the formula, and how dry you can afford the finish to feel. Low oil absorption (Kingsica S060 at 60, TR070SI at 70) suits formulas that already contain enough oil…
017What is the practical difference between S201 and S300, and between S202 and S302?Particle size is nearly the same; oil absorption is not. S201 is 7 µm at 200, S300 is 7 µm at 300. S202 is 5 µm at 200, S302 is 5 µm at 300. So these pairs let you change oil absorption without changi…
018Which grade gives soft-focus, and at what loading?The fine, mid-absorption spherical grades — 2028 at 2 µm and 3028 at 3 µm — are the usual starting point, typically at 2–6%. Soft-focus comes from the spherical shape and the pore-size distribution ra…
019Which grades are for scrub and cleansing textures?The PC series — PC20 (20 µm), PC100 (100 µm), PC150 (150 µm) and PC200 (200 µm), at oil absorption 100–130. For scrubs the particle size sets the sensation: 100–200 µm reads as a clearly perceptible s…
020Does higher oil absorption mean better oil control on skin?Not necessarily. It means the powder takes up more oil in a beaker, which is a formulation property and only an indicator of what happens on skin. On skin, oil control depends on how much powder is ac…
021My formula feels tight and dry after adding silica. How do I rebalance it?Drop the oil absorption first, then the loading, then add back slip. High-absorption silica removes part of the oil phase along with the sebum, so the film ends up under-plasticised. Moving from a 300…
022How do I stop silica from agglomerating in the premix?Wet it out before it goes into the main batch, and keep the shear high enough while it disperses. Spherical porous silica has a large internal pore volume, so it pulls binder and oil into the pores qu…
023What documentation is needed to ship silica to the EU and the US?COA per lot, TDS and SDS are the baseline. Beyond that, the requirement depends on the form and on how the customer's own product is classified. Two questions come up most often. First, whether the ma…
024Is silica a direct replacement for talc in a talc-free reformulation?It can support the claim, but it is not a texture-for-texture swap. Talc is platy and provides slip plus moderate oil absorption. Spherical silica provides oil absorption plus ball-bearing glide and s…
025What are the MOQ and lead times for Kingsica grades?Stocked standard grades move quickly at sample scale; the commercial quantity and lead time are quoted per grade and destination. The wide grade range — OA from 60 to 300, size from 2 to 200 µm — mean…
026What particle sizes are available, and how do I convert mesh to microns?Our range runs from roughly 2 µm to 200 µm. The mesh figure some suppliers quote is a screen size, not a particle size, and the conversion is approximate: 325 mesh is about 44 µm, 800 mesh about 18 µm…
027Is cosmetic-grade silica safe on skin, and what should I check in the documentation?The material is amorphous synthetic silica, not crystalline quartz, and that distinction is the whole safety story — crystalline silica is the respirable hazard, amorphous silica is not, and cosmetic …
028Oil absorption or specific surface area — which number should drive my choice?Oil absorption is the number to formulate with; specific surface area is the number that explains it. The two track each other closely, because more surface means more oil held on it, so a grade at 30…
029How does silica compare with talc and kaolin for oil control?Silica absorbs the most per unit weight, kaolin next, talc the least — and that ordering is exactly why talc-free reformulations keep running into shine. A porous silica at 200–300 oil absorption take…
Titanium Dioxide13 answers
030Rutile or anatase: which one should I start with?Rutile for almost everything, anatase only where you want a specific optical effect. Rutile scatters light more efficiently and is the grade the industry builds coverage around, so it reaches the same…
031Your rutile grades run from 210 to 420 nm. How does size change the result?Smaller particles give more covering power per kilo but scatter less light back at you; larger ones give a brighter, cleaner white and easier wetting. T-60 at 210 nm and CR50 at 250 nm and T-90 at 280…
032What is the difference between aluminium hydroxide coating and aluminium hydroxide plus silica?Alumina alone gives photostability and dispersion; adding silica on top improves the surface's resistance to the photoactive reaction that TiO2 can trigger in a formula. That matters when the TiO2 sit…
033What loading do you see in foundation, pressed powder and sunscreen?Foundation usually lands at 5–12%, pressed powder at 3–8%, and sunscreen at whatever the SPF target dictates — often 3–8% for a moderate SPF in combination with an organic filter, higher for mineral-o…
034Is your TiO2 nano or non-nano? How do I document that?It is non-nano. The rutile grades are specified at 210–420 nm mean particle size and the anatase grades at 200–220 nm, all well above the 100 nm threshold used in most nano definitions. For a customer…
035My coverage dropped after switching to a finer grade. Why?Because fines that are not fully dispersed act as light scatterers in the wrong size range — they dull the film instead of whitening it. Going from a 400 nm grade to a 210 nm grade roughly doubles the…
036Does TiO2 whiten as much in a water-based system as in an anhydrous one?Less, and the gap is bigger than most people expect. TiO2 needs air voids around the particle to scatter efficiently. In an anhydrous base the oil wets the surface only partially, leaving those voids;…
037What paperwork comes with each lot?A batch COA, the TDS, and the SDS. Additional documents — heavy metal statements, allergen declarations, non-nano statements, REACH registration status — are issued on request against the specific gra…
038Which grade should I use in a compact where hardness matters?T-48 or T-02 in rutile, or T-01 in anatase. Hardness in a pressed compact comes from particle packing and from the binder, and coarser particles pack into a denser, stronger structure. The 400–420 nm …
039What are MOQ, lead time and packaging?MOQ is typically 25 kg for a stock grade and 100–200 kg for a production run of a non-stock grade. Lead time is roughly 7–15 working days depending on grade and quantity; stock items ship sooner. Stan…
040My TiO2 leaves a chalky white cast. How do I fix it?White cast is TiO2 doing its job too well in the wrong place. It scatters across the visible spectrum, and past a certain loading that scatter reads as a white film rather than as coverage. Three leve…
041Does TiO2 cause photocatalytic degradation, and how do I control it?Uncoated TiO2 is photocatalytic. It generates radicals under UV, and in a formula that shows up as fragrance breakdown, colour fading and, in the worst case, rancidity in the oil phase. This is a real…
042Is TiO2 permitted in lipstick, and does it change the feel?Yes, and it is common — it is what gives a lipstick opacity and makes a red read as red rather than as a stain. Two caveats. The regulatory one: TiO2 for lip use is permitted in most markets, but the …
Calcined Kaolin11 answers
043Calcined or hydrous kaolin — what is the actual difference in the formula?Calcination drives off the water of crystallisation and sinters the platelets, which raises whiteness, hardness and oil absorption. Hydrous kaolin stays softer and is used where you want a clay that d…
0445000 at 2 µm or GL03 at 3 µm?2 µm if you want maximum oil absorption and a matte finish; 3 µm if you want easier dispersion and a less dry feel. The finer grade has more surface per gram, so it takes up more sebum and gives a fla…
045Why is calcined kaolin used for press strength?Because the calcination step creates a harder, more angular particle that interlocks under pressure instead of sliding past its neighbours. Soft platy fillers such as talc and mica slide, which is wha…
046How much can I load, and what does it do to skin feel?5–15% is the usual band. Below 5% you mostly get a mattifying effect with little structural contribution; above 15% the dryness becomes the dominant sensation. At 8–12% you get both the oil absorption…
047Does higher calcined kaolin loading mean better oil control?Up to a point, then it plateaus and starts to cost you comfort. Oil absorption rises with loading, but once the powder is saturated the excess oil simply sits on top of the film, and the dry feel of a…
048Can calcined kaolin replace part of the talc in a pressed powder?Yes, and it is one of the easier substitutions — 20–40% of the talc is a reasonable starting point. Both are platy aluminosilicates, so the texture translates without a big reformulation. What changes…
049Is the whiteness stable across lots?The specification holds whiteness within a defined band, but calcined kaolin is a natural-mineral product, so there is lot-to-lot variation inside that band. For a tinted product, that matters more th…
050What does the 'global regulation compliant' series change?It is produced and tested against a tighter heavy-metal profile, which is what most market-specific cosmetic questionnaires actually ask about. The base grade meets the general cosmetic specification.…
051How does it disperse, and what equipment do I need?It wets out slowly but disperses cleanly once wetted — the difficulty is the initial wetting, not the breakdown. In a dry powder blend it is simply blended. In a slurry or a cream it needs shear: a hi…
052What is the MOQ and how is it packed?25 kg per bag as standard, with 500 kg jumbo bags for volume orders. MOQ for a stock grade is 25 kg; a non-stock grade is typically 100–200 kg. Lead time runs about 7–15 working days. Samples are 1 kg…
053My pressed powder crumbles or caps after I added kaolin. What went wrong?Usually too much kaolin, or too little binder to compensate for it. Calcined kaolin is a strong oil absorber, so it takes binder out of circulation — the pan is under-bound even though the binder perc…
Talc13 answers
054Your grades run from 5 to 16 µm with oil absorption from 40 to 81. How do I choose?Choose by oil absorption first, particle size second — the two move together but not perfectly, and oil absorption is what drives the skin feel. LS-325 at 16 µm and oil absorption 40 is the slip grade…
055LS-2500 and LS-6008 are both listed at 8 µm but with different oil absorption. Which number do I trust?The oil absorption figure — the size is a nominal mean, and the two grades are produced on different lines. LS-2500 reports 8 µm with surface area 8 and oil absorption 81; LS-6008 reports 8 µm with su…
056Is your talc asbestos-free, and how is that documented?Yes. Every lot is tested for asbestos and the result is reported on the COA, which is the document a customer questionnaire is actually asking for. The test is by a recognised method on the incoming o…
057What are the current regulatory pressures on talc, and how should I plan?The direction is toward tighter documentation and, in some markets, restricted use in specific product types. The practical response is to keep a documented substitution path rather than to wait. Two …
058What is the BVL series, and do I need it?It is the same talc held to the German BVL heavy-metal limits, which are stricter than the general cosmetic specification and are used as a reference by a number of European customers. You need it if …
059What loading do you see in loose powder versus pressed powder?Loose powder 40–70%, pressed powder 25–45%. Talc is usually the base, not an additive. In loose powder the ceiling is feel: past about 70% the powder starts to fly and the pay-off becomes uneven. In p…
060How do I keep talc from flying during filling?Reduce the fine fraction and control humidity, in that order. Airborne dust during filling is mostly the sub-10 µm fraction, and a coarse grade such as LS-325 generates noticeably less of it than a 5 …
061Can I replace talc completely?In most formulas, yes, but it takes more than one material. Talc does three jobs at once — slip, oil absorption and cost — and no single substitute does all three at the same price. The usual approach…
062Does particle size affect adhesion and wear?It affects them through the oil absorption path more than directly. Finer talc with higher oil absorption takes up more of the binder and the sebum, which can improve wear because the film stays drier…
063What is the MOQ, and can you ship in a specific packaging?MOQ is 25 kg for a stock grade, 100–200 kg for a non-stock grade. Lead time 7–15 working days, samples 1 kg. Standard packing is 25 kg paper-plastic composite bags; 500 kg and 1000 kg jumbo bags are a…
064If I cut the talc in a loose powder by half, what has to change to keep the same feel?Four things, and skipping any one of them is why talc reduction usually fails on the first trial. Slip has to be replaced, not just the volume. Talc's glide comes from its platy structure, so the dire…
065Can talc be used in eye products, and what are the limits?It is permitted in eye products in most markets, and traditionally pressed eyeshadow was built on it. The limits are practical rather than categorical. The first is dust. Eye products are applied clos…
066Does talc cake up once it absorbs oil?Talc absorbs comparatively little oil and absorbs it slowly, so it is one of the less caking materials in a powder — that is part of why it was the default for so long. What caking it does show usuall…
Wet Ground Mica13 answers
067Natural mica or synthetic fluorphlogopite?Natural for cost and for a slightly more 'real' lustre; synthetic for purity, whiteness and a cleaner regulatory story. Wet-ground natural mica carries the natural trace elements of the mineral, which…
068Where does sericite fit, and why is it priced differently from mica?Sericite is a fine-grained muscovite with a smaller platelet and a more matte appearance. It is the grade you use when you want the platy structure of mica without the sparkle. The difference is optic…
069How does particle size change the look?Coarser platelets give more sparkle and more visible shimmer; finer ones give a softer sheen and more coverage. On a 6 to 20 µm ladder, 20 µm (Kingcovite 71) gives the most pronounced pearlescent effe…
070Can mica carry a pressed powder on its own if I remove the talc?It can carry the structure, but not the oil control. Mica is platy like talc and presses well, and its lower bulk density means you use less by weight for the same volume. What it does not do is absor…
071Why is synthetic fluorphlogopite whiter than natural mica?Because it is grown from a controlled melt rather than mined, so it has none of the iron and other trace colourants that tint a natural mineral. Natural mica's colour varies by ore body, which is why …
072Is there a BVL grade in the mica range?Yes — Kingcovite 6710 at 10 µm, held to the German BVL heavy-metal limits. It sits in the synthetic fluorphlogopite group, which is where the strictest market requirements usually land, because the sy…
073What loading should I use in eyeshadow and in face powder?Eyeshadow 20–50%, face powder 5–25%. In eyeshadow, mica is often the structural base — it provides the press strength, the pay-off and the pearl, and the pigment sits on top of it. Below 20% the shado…
074Why do my pressed eyeshadows show streaks or a directional sheen?Because the platelets align during pressing, and the alignment is not uniform. Platy materials orient parallel to the pressing surface, which is what produces the sheen — but if the fill is uneven or …
075What is the MOQ and what packing do you use?25 kg per bag, 500 kg jumbo bags available. MOQ 25 kg for stock grades, 100–200 kg for non-stock. Lead time is about 7–15 working days; samples are 1 kg and ship with COA and TDS. Mica is a low-bulk-d…
076Wet-ground or dry-ground mica — what changes in the formula?Wet grinding delaminates the platelets in a liquid medium, so you get thinner, wider, more intact sheets with a narrow size distribution. Dry grinding fractures them, which produces a broader spread a…
077Where does mica's pearlescence come from, and how is it different from a pearlescent pigment?The two are different effects, even though both get called pearl. Mica's own sheen is geometric. Flat transparent platelets align parallel to the surface and reflect light specularly off many layers a…
078Why does mica feel so good on skin?Because it is flat, and flat things lie down. The platelets are thin relative to their width, so they settle parallel to the skin instead of standing on edge, and the surface your finger meets is a sm…
079Can mica be used in liquid foundations and cushions?Yes, and it is common in both, but the behaviour is different from a powder. In a fluid the platelets settle and orient horizontally during storage, so the product can develop a soft sediment and, on …
No answer matches your search in this topic.
Not finding an answer?
Talk to our technical teamDescribe your formulation system and the problem — the technical team replies within one business day, and can arrange samples at the same time.