You are using an outdated browser. For a faster, safer browsing experience, upgrade for free today.

Regulatory News

Regulatory News EU Microplastics Rule: Mineral Powder Scope

KingPowder Technical Team 69

Since 17 October 2023, cosmetic formulators in Europe have been asking suppliers a question that sounds simple and is not: is this powder a microplastic? The answer turns on what the regulation actually restricts. It does not restrict particles. It restricts synthetic polymer microparticles, in which the particle is only the carrier and the polymer is the substance that triggers the rule.

Mineral powders are inorganic, so the substance question usually resolves in their favour. The complication sits in the finishing steps, where surface treatment and coating introduce organic material onto the particle.

1. The definition needs three conditions at once

Commission Regulation (EU) 2023/2055 of 25 September 2023 added entry 78 to Annex XVII of Regulation (EC) No 1907/2006. Its subject is synthetic polymer microparticles (SPM). A particle qualifies only when three conditions hold together:

  • It is a solid polymer.Liquid polymers are outside the definition.
  • It is present in the particle at 1% by weight or more, or it builds a continuous surface coating on the particle.These are alternatives. Coated powders are engaged by the second limb, not the first.
  • Size.At least 1% by weight of the particles have all dimensions at or below 5 mm, or a length at or below 15 mm with a length-to-diameter ratio above 3.

The regulation also excludes polymers that occur in nature without chemical modification, polymers that are degradable, polymers with a solubility above 2 g/L, and polymers whose chemical structure contains no carbon atoms. Those exclusions do real work in practice, and they are worth keeping at hand when a treatment agent comes into question.

2. Why a mineral powder sits outside the scope

Boron nitride, silica, titanium dioxide, zinc oxide, talc, mica and kaolin are inorganic mineral substances. None of them is a synthetic polymer, so none of them is an SPM. Synthetic fluorphlogopite is manufactured rather than mined, but it is still an inorganic mineral, and the regulation restricts synthetic polymers. The word synthetic in the title is not the operative one; the word polymer is.

The Commission's explanatory guide states the position plainly for the adjacent case of effect pigments: glitter made of glass, metal, natural or inorganic material is not regarded as microplastics and falls outside the restriction. Mica-based pearlescent pigment producers have followed the same reasoning, certifying that their products consist entirely of inorganic mineral substances with no polymer used as a constituent.

Being outside the scope and being able to demonstrate it are different positions. A buyer's technical review does not stop at the conclusion; it asks what the conclusion rests on. The useful part of a statement is therefore the composition record, not the sentence at the top of the page.

3. Surface treatment is where the judgement lives

For a powder producer this is the only section that requires real work. The continuous surface coating limb places coated powders directly in view. Three questions, taken in order, resolve most cases.

Is the treatment agent a polymer.Stearic acid, stearates and isostearic acid are fatty acids and their salts, and are not treated as polymers. Titanate, aluminate and silane coupling agents are small molecules rather than polymers. Polydimethylsiloxane and its crosslinked derivatives, PMMA coatings and polyurethane coatings are synthetic polymers, and they move the case to the next question.

Does it form a continuous coating.The regulation uses the word continuous. A monomolecular layer grafted onto the surface by a reactive silane and a film formed from a polymer dispersion are not the same physical situation. This step normally depends on documentation from the treatment supplier rather than on inference by the powder producer.

What is the polymer's share of the particle weight.The threshold is 1%. Typical surface treatment loadings on mineral powders fall between 0.5% and 3%, which straddles the line. A general statement that the loading is small does not answer the question; the formulation sheet and batch records do.

Two exclusion routes remain open at this point. A polymer that is degradable, or has a solubility above 2 g/L, or contains no carbon in its structure falls outside the definition. Water-soluble treatments use the solubility route.

4. Transition periods are set by use, and buyers work backwards from them

The restriction applies on different dates according to product type. The cosmetic entries are:

  • Rinse-off products: from 17 October 2027
  • Leave-on products, fragrance encapsulation, medical devices without microspheres: from 17 October 2029
  • Lip, nail and make-up products: from 17 October 2035, with a label stating that the product contains microplastics required from 17 October 2031
  • Loose plastic glitter and plastic microbeads: from 17 October 2023, with no transition period

A transition period protects the act of placing a product on the market. It does not freeze the formula. Buyers in the rinse-off category are already locking in replacements during 2026, and buyers in the make-up category are asking for a position at formula freeze even though their date is later.

One threshold is frequently misread. The 0.01% by weight concentration limit applies to SPM intentionally added to mixtures. It is a test for formulators working with SPM, not an exemption threshold for inorganic powders, and the two should not be used interchangeably.

5. What changed in 2026, and what did not

Entry 78 was amended by Commission Regulation (EU) 2026/1168 of 1 June 2026. That amendment clarifies the derogations for medicinal and veterinary medicinal products, adds a derogation for product and process oriented research and development at quantities of one tonne per year or less, and from 22 June 2028 limits the derogation for SPM permanently incorporated into a solid matrix to intended end uses of one year or longer.

The definition of SPM, the 0.01% concentration limit and the transitional periods in paragraph 6 were not changed by that amendment. This matters when reading secondary summaries: some circulating versions describe the 2026 amendment as a change to the definition, which it is not.

A separate obligation began on 17 October 2025. Suppliers of SPM must provide information on use and disposal, a compliance statement, and quantity or concentration data through safety data sheets, labels and other supply-chain documents. The obligation attaches to products containing SPM. An untreated inorganic powder does not trigger it.

6. What a statement should contain

A statement that only asserts the absence of microplastics invites three follow-up questions and answers none of them. Five elements make it usable:

  • The full composition of the product, stating that all constituents are inorganic mineral substances and that no polymer is used as a constituent
  • The chemical identity of any surface treatment and its typical loading; where the agent is a polymer, whether it forms a continuous coating and whether its share of particle weight stays below 1%
  • A statement that the product does not rely on any derogation under entry 78, because compliance follows from being outside the SPM definition rather than from an exemption
  • Confirmation that the loose powder carries no organic polymer surface coating, and, where anti-dusting or wetting agents are present, their physical form and solubility
  • The regulation version and the date the statement was issued

The last item is the one most often omitted and the one a compliance file needs. Entry 78 has been amended once already, and a statement without a date cannot be mapped to a version two quarters later.

Three practical steps follow. Build a table of every surface treatment in the current range and mark which agents are polymers. For products using polymer coatings, request three items from the treatment supplier: chemical identity, whether a continuous coating forms, and the typical loading in the powder. Then issue statements as dated, versioned documents so a buyer's file can hold them alongside a specific regulation version.

This article describes the structure of the restriction and the reasoning path it implies. It does not confirm the compliance status of any specific product. Substance-level decisions should be checked against supplier technical documentation, the current legal text and the explanatory guide, and confirmed with the EU importer or a regulatory adviser before use in an external statement.

Become a Distributor