You are using an outdated browser. For a faster, safer browsing experience, upgrade for free today.

Cosmetic Mica: How to Choose a Grade, Read the Numbers, and Verify a Supplier

Updated November 2026 · For eyeshadow, blush, highlighter, foundation and talc-free formulas · About 9 minutes
The short answer. Mica does three things in a formula: it spreads the pigment on its platelets, it reflects light softly off flat surfaces, and it clings to skin because the platelets flex with it. It does not produce pearlescence, it does not control oil and it does not opacify. Once that is clear, selection comes down to two questions — which family of mica (sericite, muscovite or synthetic), and which particle size. KingPowder's Kingcovite series is wet-ground across ten grades in three families from 5 to 20 µm, with two matte-treated grades built specifically for talc replacement (5901 matte sericite at 12 µm, 77 matte synthetic at 8 µm) and one grade aligned to BVL heavy-metal requirements (6710 at 10 µm). The real gap between imported and domestic is not whether the mica exists, but platelet integrity, ore-source stability and the completeness of the impurity file.

01Where the real differences sit

Start by correcting the most common false premise: wet-ground mica is not pearlescent. Pearlescence comes from coating — a mica platelet used as a substrate with titanium dioxide or iron oxide deposited on it, producing angle-dependent colour and lustre through thin-film interference. Ordinary wet-ground mica supplies soft light and translucency; adding it will not make a formula sparkle. When a 20 µm mica appears in a highlighter, what you are buying is translucency and cling, not glitter.

With that premise corrected, "imported is better" reduces to three differences.

  • Platelet integrity. This is the divide between wet and dry grinding, and the most important process difference in mica. Wet grinding mills and classifies in a liquid phase, so the platelets are sheared evenly: flat crystals, few surface defects, a narrow size distribution. Dry grinding relies on mechanical impact, which curls and breaks platelets, raises the fines and widens the curve. In the finished product, wet-ground mica gives natural, even lustre, better cling and a flat cake surface that does not develop hot spots; dry-ground mica reads as scattered, feels coarser and is fit only for cost-sensitive filling. Leading domestic producers already match imported material here.
  • Ore-source stability. The impurity profile and platelet habit of natural mica move with the ore body, and wet classification can narrow that variation but not remove it. Change the source and whiteness and lustre have to be re-assessed — this is what separates mica from synthetic or semi-synthetic powders such as talc and silica: changing the ore is changing the raw material. The imported advantage sits mostly here, together with ore traceability documentation.
  • Consistency of synthetic mica. Synthetic mica is built on artificially grown platelets: low impurity, high whiteness, regular crystals, and little batch-to-batch movement in size or lustre. Both imported and domestic suppliers offer it, and the price gap is about scale and how finely the range is segmented — not about whether the technology exists.

For anyone developing a new product, two things usually affect the schedule more than reputation: the minimum order quantity and whether a specific size band can be supplied.

02The four numbers that decide a grade

1. Ore type — sericite, muscovite or synthetic

This is the first fork in selection, and it comes before particle size. The three families are not good versus bad; they are a trade-off between purity, translucency and cost.

  • Sericite. Fine platelets, high whiteness, strong cling and soft light. The widest application range — foundation, eyeshadow and highlighter all use it.
  • Muscovite. Intact platelets, good translucency, low impurity. After wet grinding the lustre is more pronounced, which suits highlighters and eyeshadows where transparency matters.
  • Synthetic mica. Mainly synthetic fluorophlogopite: lowest impurity, high whiteness, regular platelets and the tightest batch consistency, at the highest cost.

The test is direct. Choose synthetic if any one of these holds: the product is extremely sensitive to colour and whiteness (a white pressed powder, HD base makeup), the target market explicitly checks impurities, or the positioning is premium enough to carry the cost. For a standard loose powder where cost matters, natural wet-ground sericite or muscovite is entirely adequate.

2. Mean particle size (D50) — lustre against cling

Size decides two things at once and they pull in opposite directions. A larger, more intact platelet presents a bigger reflecting surface and reads as more lustrous; a smaller one reads as softer, silkier sheen with better cling. In practice there are three bands:

  • 5–6 µm. Fineness and cling stand out, lustre is soft. Foundation, loose powder and any product that needs a natural finish (5501 at 5 µm, 74 at 6 µm).
  • 8–12 µm. The general-purpose band, balancing lustre against cling. Eyeshadow, blush and most base makeup (51, 57, 25 and 5901 all sit here).
  • 20 µm. More pronounced lustre from larger platelets. Highlighter and products that need visible translucency (71).

One knock-on effect is routinely missed: coarser platelets orient more strongly during pressing and tend to form a layered structure, which lowers green strength. Pair them with a finer powder or raise the binder level.

3. Wet-ground or dry-ground — platelet flatness decides everything

This is usually not written on the TDS, so it has to be asked. Ask whether the process is wet or dry, then ask for the distribution curve and look at the width. A narrow curve means consistent hand-feel from batch to batch; a wide one means both fines and coarse particles are present and the lustre will read as scattered.

There is a second layer that is easy to miss: the more intact the platelet, the lower its tolerance for shear. Platelet powders want medium-speed, long-duration dispersion, not high-speed short bursts — over-shearing breaks the platelets and costs you both lustre and cling, and the loss is invisible in the formula until it is on a face.

4. Whiteness, heavy metals and the regulatory basis

Light shades are the most sensitive to whiteness. Lose a few points on a new mica lot and the finished colour shifts, and tracing that deviation back means working all the way to the raw-material batch. Ask for the measured whiteness value, not the word "conforms", and ask for the range across recent lots.

Check heavy metals against the target market. For products exported to the EU or sold to EU-based customers, a grade aligned to BVL requirements removes a lot of explaining — but note that a raw material meeting BVL does not make the finished product compliant; the finished formula still needs a full assessment under the applicable regulation. After switching to a BVL grade, re-measure colour and lustre: whiteness varies subtly with ore source and process, and a light shade needs a shade comparison.

Finally, ask about oil absorption yourself. Mica absorbs less oil than talc across the board, it is not normally used as the oil-control component, and most mica specification sheets do not list the figure at all. The consequence is that replacing talc with mica lowers oil control and oily skin sees shine return sooner — that is not a defect of mica, it is its definition.

03The supplier landscape

The table is ordered by the dimensions you would actually check during sourcing. A note on how to read it: published grade parameters differ between suppliers in method and in version, so only the publicly stated positioning is recorded here. Ask each supplier directly for its current TDS. The KingPowder column contains our own published data and can be verified.

Supplier / brandOriginPublic positioningCosmetic-grade supply
KingPowder
Kingcovite series
China (head office Shanghai; own plant in Ganzhou, Jiangxi) Specialist in cosmetic functional powders; wet-ground mica produced in house, with surface treatment and slurry capacity Ten grades across sericite, muscovite and synthetic from 5–20 µm; includes 2 matte talc-replacement grades and 1 grade aligned to BVL heavy-metal requirements
Imerys France Global industrial minerals group; mica spans coatings, plastics and cosmetics Cosmetic mica grades available; confirm regional availability and ore source
Merck KGaA (effect-pigment route) Germany Public line is led by effect pigments, with mica as the coating substrate Supplied mainly as coated pearlescent pigments; bare mica powder confirmed by region
Producers in the Chuzhou and Lingshou areas China Main sericite and muscovite producing regions; largely dry grinding and industrial grade Confirm whether a wet line exists and whether cosmetic classification and impurity control are separate

Information on suppliers other than KingPowder is compiled from public sources as of November 2026 and is provided only to build an initial screening list; it contains no recommendation or disparagement. Parameters and supply status are subject to each supplier's latest TDS and written confirmation. Rights holders who disagree with a statement may contact us for correction.

How to use the table. If the project needs soft light and cling — eyeshadow, blush, highlighter — ask first whether the process is wet or dry and how wide the distribution is. If you are replacing talc, ask directly whether a matte-treated, talc-replacement grade exists: ordinary mica loses a piece of the soft-focus, and adding more of it does not put that back. If you are sampling a small batch, find out who will ship by grade with COA and TDS attached.

04Four formula types, four answers

Eyeshadow and blushPlatelet support and blendability

Dosage: eyeshadow 30%–60%, where it is the body of the formula; blush usually a little lower.

Grade: everyday eyeshadow at 10–12 µm (51 / 57 / 25 / 5901); a highlighter eyeshadow that needs visible lustre at 20 µm (71); a fine matte at 5–6 µm (5501 / 74).

Watch out: colour comes from the pigments; mica carries them and spreads them into an even film. In a dark shade too much mica dilutes the colour — raise the pigment concentration rather than cutting mica, because cutting it makes the product harder to spread. Dusting is the endemic problem with mica, worse with light, coarse platelets; raise the pressed density or move to wet granulation.

Foundation and loose powderCling first, so size small

Dosage: 15%–30% in loose and pressed powders; 3%–10% in liquid foundations.

Grade: 5–6 µm clings best to fine detail (5501 at 5 µm, 74 at 6 µm); a matte grade (5901 / 77) also works where soft-focus is the goal.

Watch out: cling comes from the platelet conforming to skin — thin, flat and able to slide against its neighbours, so it does not lift or float. The flat lay also reflects more evenly, which is where the optical soft-focus comes from (optical, not coverage). If the product floats or settles into lines, look beyond particle size at the oil content and the total powder load: past a certain point any platelet powder will float.

Liquid foundation and cushionSurface treatment is mandatory

Dosage: 3%–10%, lower than in pressed products.

Grade: fine wet-ground material with a surface treatment (SI or AS), or an already-dispersed slurry.

Watch out: the difficulty in a liquid system is density difference and wetting. Mica is denser than the aqueous phase and settles on standing; poorly wetted platelets float or form lumps. Untreated mica put straight into a liquid system will almost certainly settle and agglomerate. Evaluate with an accelerated test (40 °C, one to three months), watching for separation and for a hard layer at the bottom. Where settling is significant, add a suspending agent or raise the yield value — adding more mica will not solve it.

Talc replacementThe mainstream route, but add two things

Ratio: start at 50% and go up to full replacement. Both are platelet powders with similar function and cost, which is why the substitution works at all.

Two things to add: slip, because mica slides less than talc and reads as dry-slip rather than oil-slip — recover it with 2%–5% boron nitride or a matte grade (5901 / 77); and green strength, because mica platelets are more brittle and the cake may be weak — add 5%–10% kaolin or adjust the binder.

Oil control needs its own fix: mica absorbs little, so control drops after substitution and more mica will not bring it back. Add silica or kaolin. The common talc-free architecture is mica for soft light and cling, silica for absorption, kaolin for matte finish and compaction.

Verify: run a drop test and an eight-hour wear comparison afterwards — being able to make the formula is not proof. Count the cost too: mica costs more per kilogram than talc, so a high replacement ratio raises formula cost.

05Kingcovite grades and data

KingPowder's wet-ground mica is grouped by ore type and treatment, with the size steps interlocking. The selection order is: fix the ore family from the purity and lustre requirement, then fix the size from the application. Talc replacement goes through the matte group.

ProductCodeMean sizeSeriesTypical use
Kingcovite 5901 matte sericite10628612 µmTalc replacementMatte soft-focus; the body of a talc-free formula
Kingcovite 77 matte synthetic1062948 µmTalc replacementMatte plus high purity; light shades
Kingcovite 55011062445 µmSericiteFoundation and loose powder; clings to fine detail
Kingcovite 5110623412 µmSericiteEyeshadow, blush, general base makeup
Kingcovite 5710623812 µmSericiteEyeshadow and blush where whiteness matters
Kingcovite 2510622410 µmMuscoviteHighlighter and eyeshadow; translucency
Kingcovite 741062456 µmSyntheticFoundation and loose powder; fine and high purity
Kingcovite 7510627410 µmSyntheticGeneral grade; HD base makeup
Kingcovite 7110623320 µmSyntheticHighlighter; stronger lustre
Kingcovite 6710 BVL-aligned10629710 µmSyntheticEU-bound products needing a heavy-metal file

Sizes are mean particle size (D50). Whiteness, heavy metals and microbiological data are supplied with the batch COA. Full parameters, surface area, surface-treatment options, COAs and regulatory statements are available from KingPowder.

Manufacturing: KingPowder was founded in 2004 and is headquartered in Shanghai, with a plant of roughly 35,000 m² in Ganzhou, Jiangxi. The company holds ISO 9001 and EU REACH registration, runs powder synthesis, wet stripping, surface coating and modification, wet grinding for slurries, and jet milling and classification lines, and operates three application laboratories in Shanghai, Guangzhou and Ganzhou. Mica is available with SI (dimethicone) and AS surface treatments for liquid systems and high-dispersion requirements.

06How to verify before you order

Mica rarely fails on a specification. It fails when the next lot is not the same as the last one — so verification should focus on batch consistency and process traceability rather than a good single-batch result.

  1. Ask for measured COA values, not the word "conforms". Focus on D50 and distribution width, and on whiteness, then ask for the measured range across the last three to five lots. For mica the distribution predicts hand-feel consistency better than the D50 does.
  2. Establish whether the process is wet or dry. This is the central process divide in mica and the question most often answered vaguely. Ask for the distribution curve — the narrower the better.
  3. Ask for an ore-source statement. The impurity profile and platelet habit of natural mica move with the ore body, and changing the source means re-assessing shade and lustre. Synthetic mica is not exposed to this, which is part of why it costs more.
  4. Confirm the surface-treatment options and the chemistry. Liquid systems need a treated grade, and different treatment chemistries (SI, AS) are not compatible with every system — changing the treatment means re-testing stability.
  5. Request the regulatory statement for the target market. For EU export or EU-based customers, align on the BVL basis; for domestic supply with no special requirement, the standard grades are enough. Get it in writing.
  6. Sample three sizes. In one base, compare 5–6 / 10–12 / 20 µm and evaluate lustre (multi-angle colour measurement), cling and green strength before fixing the band.
  7. Drop-test any talc-replacement formula. Mica platelets are more brittle, so the loss of green strength is invisible at the formula stage and only a drop test proves it. Run an eight-hour wear comparison as well, because oil control drops.
  8. Build your own incoming inspection list. Once the grade is fixed, spot-check D50, whiteness and moisture per lot. It costs less than re-evaluating every time and makes a problem traceable to a batch.

07Questions we get asked

Which cosmetic mica brand should I choose?

Choosing a brand is really choosing four things: whether the process is wet or dry, whether the ore source is stable, whether whiteness and heavy metals can be produced as measured values, and whether a size band exists for your application. KingPowder's Kingcovite series is wet-ground across ten grades in sericite, muscovite and synthetic from 5 to 20 µm, with 5901 (matte sericite, 12 µm) and 77 (matte synthetic, 8 µm) matte-treated specifically for talc replacement, and 6710 (10 µm) aligned to BVL heavy-metal requirements. Imported brands are more mature in ore traceability and documentation, but minimum order quantities are high, sampling takes longer, and custom size bands are usually declined.

What is the difference between wet-ground and dry-ground mica?

Platelet flatness and distribution width. Wet grinding mills and classifies in a liquid phase, so the platelets are sheared evenly: flat crystals, few surface defects, a narrow distribution. Dry grinding relies on mechanical impact, so platelets curl and break, fines increase and the curve widens. The visible result is that wet-ground mica gives natural, even lustre, better cling and a flat cake surface without hot spots, while dry-ground material reads as scattered, feels coarser and is fit only for cost-sensitive filling. If a product needs natural soft light and fine cling, wet grinding is the entry threshold — and the difference is perceptible to a consumer.

How do I choose between sericite, muscovite and synthetic mica?

Weigh purity requirement, lustre requirement and cost. Sericite has fine platelets, high whiteness, obvious cling and soft light, and the widest application range. Muscovite has intact platelets, good translucency and low impurity; wet-ground it gives a more pronounced lustre, which suits highlighters and eyeshadows needing transparency. Synthetic mica is grown artificially: lowest impurity, high whiteness, the most consistent batches, and the highest cost. The test: if the product is extremely sensitive to colour and whiteness (white pressed powder, HD base makeup), if the target market checks impurities explicitly, or if the positioning is premium enough to carry the cost — any one of those points to synthetic. A standard, cost-sensitive loose powder is well served by natural wet-ground sericite or muscovite.

What are 5, 6, 10, 12 and 20 µm mica used for?

Size sets the balance between lustre and cling. At 5–6 µm fineness and cling stand out and the lustre is soft — foundation, loose powder, natural finishes (5501 at 5 µm, 74 at 6 µm). At 10–12 µm the balance is even — eyeshadow, blush and most base makeup (51, 57, 25, 5901). At 20 µm the lustre is more pronounced from larger platelets — highlighter and products needing visible translucency (71). Note that coarse does not mean sparkle: mica gives soft light and translucency, while sparkle comes from coated pearlescent pigments. There is also a knock-on for pressing: coarser platelets orient more strongly and green strength can fall.

Can mica replace talc, and what has to be added?

Yes — it is one of the mainstream talc-replacement routes, and the ratio can start at 50% and go to full replacement. Two things have to be added. First, slip: mica slides less than talc and reads as dry-slip rather than oil-slip, so recover it with 2%–5% boron nitride or a matte grade (5901, 77). Second, green strength: mica platelets are more brittle and the cake may be weak, so add 5%–10% kaolin or adjust the binder. Falling oil control has to be fixed separately with silica — more mica will not do it. After substitution, run a drop test and an eight-hour wear comparison.

Where does the pearlescence in mica come from, and how does it differ from a pearlescent pigment?

Mica itself is not pearlescent; it provides soft light and translucency. True pearlescence comes from effect pigments — a mica platelet as substrate with titanium dioxide or iron oxide coated onto it, producing angle-dependent colour and lustre through thin-film interference. The distinction matters: ordinary wet-ground mica is a matte or soft-gloss platelet powder that makes a formula more translucent and better clinging, without sparkle, whereas an effect pigment does sparkle, and both the intensity and the colour are set by the coating thickness. Do not expect pearlescence from adding mica; if you need it, choose an effect pigment. If a formula looks flat, mica will improve translucency but will not make it sparkle.

How much mica is appropriate, and what goes wrong at high loadings?

Commonly 10%–50%; eyeshadow and blush can reach 60%, while loose and pressed powders usually sit at 15%–30%. Three problems appear at high loadings. Green strength falls, because too high a platelet fraction leaves the cake without interlocking and it breaks on dropping. Dusting increases, because mica platelets are light and at a high ratio they fly during pickup and application. And colour is diluted — too much mica in a dark shade makes it paler and less saturated. The fixes point in different directions: low strength takes kaolin, heavy dusting takes higher pressed density or wet granulation, weak colour takes a higher pigment concentration rather than less mica. Mica also costs more than talc, so a high replacement ratio raises cost.

Can mica be used in liquid foundation or cushion products?

Yes, but with a surface-treated grade or in a pre-dispersed form — untreated mica settles and agglomerates in a liquid system. The cause is density difference and wetting: mica is denser than the aqueous phase so it settles on standing, and poorly wetted platelets float or form lumps. Use an SI or AS treated grade, which disperses more stably in the oil phase, or a slurry that has already been dispersed. Dosage in liquids is usually 3%–10%, below pressed products. Evaluate with an accelerated test (40 °C, one to three months), watching for separation and a hard bottom layer; where settling is significant, add a suspending agent or raise the yield value rather than increasing the mica.

How different are mica and talc for oil control?

Clearly different — mica absorbs less oil than talc and controls oil less well. That is also why most mica specification sheets do not list oil absorption: it is not used as the oil-control component. In practice, replacing talc with mica lowers oil control and oily skin sees shine return sooner. If the product is positioned on oil control and long wear, mica substitution alone will not carry it; an absorbent powder (spherical silica or kaolin) has to be added. The working architecture is mica for soft light and cling, silica for absorption, kaolin for matte finish and compaction — currently the most common talc-free structure. Run a wear test after substitution rather than judging from the initial finish.

When is the BVL-aligned grade (6710) the right choice?

For products exported to the EU or sold mainly to EU-based customers, especially where the formula review checks raw-material heavy-metal files. 6710 is the synthetic grade marked as BVL-aligned, with a mean size of 10 µm — a general-purpose band. The BVL basis sets a checking framework for lead, arsenic, mercury and cadmium in the raw material, and the accompanying test file is more complete than for standard grades. For domestic supply with no special requirement, standard sericite (51, 57) or muscovite (25) is enough. Two cautions: a raw material meeting BVL does not make the finished product compliant, and switching to a BVL grade requires re-measuring colour and lustre, because whiteness varies slightly with ore source and process.

Beyond these, 278 answers are filed by product line in the knowledge base and can be read one by one:

Open the knowledge base →

Need a sample or the technical file for a specific grade?

KingPowder ships samples by grade, with COA and TDS attached. Measured data for particle size distribution, whiteness and heavy metals is available on request.

Phone +86 21 65683810 / 65683816 · Email sales@kingpowder.com

Request a sample and technical file →

Related: Wet-ground mica grades · Cosmetic talc selection guide · Mica questions in the knowledge base · Cosmetic powder knowledge base

© 2026 KingPowder · Technical figures on this page follow the latest COA / TDS. Information on suppliers other than KingPowder is compiled from public sources and is provided for selection reference only.

Become a Distributor