Kaolin is one of the most abundant non-metallic minerals in China — the ore is not scarce. So on kaolin, "imported is better" has to be broken into a more specific question: can the calcination be controlled, and can a cosmetic-grade impurity basis be produced?
Three differences are real.
Seen from the other side: if the product needs oil control plus green strength and has no strict requirement for whiteness or extreme matte, domestic calcined kaolin is entirely sufficient, and the price difference is better spent on formula verification. It is for a high-whiteness pressed powder or a premium base where the matte finish has to be extremely stable that paying for imported batch consistency makes sense.
The difference is one sentence long: whether the structural water has been removed. The consequences follow in a chain.
One further difference is easy to overlook and matters a great deal in hot, humid markets: behaviour after absorbing oil. A calcined grade keeps good powder flow once it has taken up oil; a water-washed grade turns sticky and cakes. In a finished product that shows up as a hardened pan surface and powder that becomes hard to pick up. So for a pressed product, even a cost-reduction exercise, swapping calcined for water-washed directly is not advisable.
2 µm leans toward coverage and fineness, 3 µm toward spread and cost. The rule: the smaller the particle, the larger the surface area, and the more pronounced the adsorption and coverage — but the more readily it agglomerates, the harder it disperses, and the more binder pressing requires.
Two things decide it. First, the proportion of other fine powders already in the formula: if there is a lot of 2 µm-scale material (fine talc, spherical silica), adding 2 µm kaolin pushes the whole system too fine and the pan becomes brittle. Second, the target finish: strong matte takes the finer grade, a natural translucent look takes the coarser one. The overall difference between the two grades is not large, so in a real trial pay more attention to batch consistency and the stability of oil absorption than to the size figure alone.
Kaolin adsorbs oil through active sites on the particle surface and in the interlayer regions. Capacity is moderate and adhesion remains good after absorption, which means the oil-control curve is gentle and sustained — suited to everyday base makeup and unlikely to leave skin tight.
For reference: spherical porous silica holds oil inside its pores, has a large pore volume and reaches 150–300, so control is strong and fast — good for oily skin and long wear, but at high loadings the dryness is obvious and it can pull so much of the oil phase out that the bulk hardens. Starches adsorb through the surface and slight swelling: smooth feel, low cost, but limited capacity, prone to caking after absorption, and requiring preservative support.
The selection logic: pressing and matte point to kaolin; strong oil control and soft-focus point to silica; smoothness and cost point to starch, with stability assessed. When combining them, watch the total absorption — stacking all three dries a formula out very easily, which in a low-oil powder shows up as drag on application and a cracked pan surface. Fix the oil-control target with one powder, then trim with the second; do not run three at high ratios at once.
Green strength comes from mechanical interlocking and contact area between particles. Calcined kaolin is a mixed structure of platelets and irregular particles with a fine size and a large surface area, so pressing produces more contact points and a denser compact; and because its surface still adheres well after absorbing oil, it holds both the oil and the powder together, reducing spring-back and dusting after pressing. This is the one thing talc cannot replace — too high a proportion of talc makes the bulk too slippery, interlocking is lost and green strength falls.
The matte effect comes from surface roughness: after calcination the particle surface is irregular, light scatters more diffusely and the perceived gloss drops.
On whiteness, light shades are sensitive, so ask for measured values rather than lower limits. Check heavy metals against the target market, and for a product exported to several markets, set the specification against the strictest one so that a single formula does not turn into several versions.
The table records publicly stated positioning only. Cosmetic-grade parameters differ between suppliers in method and version, so ask each one for its current TDS; the KingPowder column contains our own published data and can be verified.
| Supplier / brand | Origin | Public positioning | Cosmetic-grade supply |
|---|---|---|---|
| KingPowder Kingaolin series |
China (head office Shanghai; own plant in Ganzhou, Jiangxi) | Specialist in cosmetic functional powders; calcined kaolin produced in house, with surface treatment and formula support | Two grades: Kingaolin 5000 (2 µm, standard basis) and GL03 (3 µm, aligned to global regulations) |
| BASF | Germany / USA | Cosmetic functional powders and additives as a main business, with calcined kaolin as one functional filler class | Several calcined kaolin grades; specifications and regional availability confirmed on request |
| Imerys | France / UK | Global industrial minerals group; kaolin spans paper, ceramics, coatings and specialty applications | Cosmetic-suitable kaolin grades available; confirm by region |
| Thiele Kaolin | USA | Dedicated kaolin producer running both water-washed and calcined lines | Some grades used in personal care; confirm cosmetic-grade documents through the agent |
| Producers in the Longyan and Maoming areas | China | Main kaolin regions, both water-washed and calcined, largely ceramic and filler grade | Confirm separate cosmetic classification, calcination temperature control and the heavy-metal basis |
Information on suppliers other than KingPowder is compiled from public sources as of November 2026 and is provided only to build an initial screening list; it contains no recommendation or disparagement. Parameters and supply status are subject to each supplier's latest TDS and written confirmation. Rights holders who disagree with a statement may contact us for correction.
How to use the table. If the core requirement is a pan that does not crumble, ask first how the calcination curve is controlled and what the surface area is — a collapsed surface area means it was over-fired. If you export to several markets, ask whether one grade satisfies the heavy-metal basis of all of them. If you are replacing talc, ask at what replacement ratio the hand-feel is still acceptable in the supplier's own testing.
Dosage: 5%–20%. As a pressing aid, 5%–10% is enough; as the oil-control body it can go to 15%–20%.
Grade: Kingaolin 5000 (2 µm) first — a finer size gives more contact points and a denser compact. GL03 (3 µm) where cost and spread matter more.
Watch out: above 20% the risk of pressing failure rises sharply — the powder is too fine, the oil is over-absorbed and there is not enough lubrication between particles. Work in this order: check whether the dosage is too high, then restore lubrication (1%–3% magnesium stearate or a higher talc ratio), then adjust the press parameters (excessive pressure also causes spring-back and cracking). Moisture is often overlooked: a high moisture content makes the powder stick to the die and the surface go dull, so control the storage humidity.
Dosage: commonly 5%–15%, as a supporting powder rather than the body.
Grade: GL03 (3 µm) spreads more smoothly and costs less — suited to a loose powder with a high filler ratio.
Watch out: a loose powder is low in oil, and kaolin absorbs strongly while supplying little slip, so too much produces a dragging application. Three things relieve it: pair with a lubricating powder (3%–5% boron nitride, a spherical powder or talc), use a surface-treated grade (AS / SI), and give the strong oil-control requirement to silica rather than adding more kaolin.
Dosage: usually 5%–15%, adding matte and compaction to a mica-led system.
Grade: 5000 (2 µm) where a definite matte is wanted; GL03 (3 µm) where colour should stay translucent.
Watch out: eyeshadow often carries 30%–60% mica, so platelet content is high and green strength is naturally weak — kaolin supplies exactly the interlocking that is missing. In a dark shade take care: kaolin is white and covers well, so too much lightens the colour and the pigment concentration has to come up with it.
Why it works: kaolin and talc overlap in platelet filling and pressing, which is what makes partial substitution viable.
Ratio: 30%–50% usually gives a more matte, slightly stronger oil control with an acceptable loss of slip. Full replacement dries the formula out noticeably and the pan may become brittle from lack of lubrication.
Adjust two things: restore slip (2%–5% boron nitride or a higher mica ratio) and re-assess green strength with a drop test. If the purpose is to avoid talc-related concerns, full replacement is technically possible, but accept the cost to feel and cost, and recover slip with another platelet powder.
KingPowder's calcined kaolin comes in two grades split by regulatory basis, with the sizes interlocking. The selection order is: fix the regulatory basis (export or not), then fix the particle size from the fineness the formula needs.
| Product | Code | Mean size | Regulatory basis | Typical use |
|---|---|---|---|---|
| Kingaolin 5000 | 106324 | 2 µm | Standard | Pressed powder; base makeup needing a definite matte and coverage |
| Kingaolin GL03 | 106329 | 3 µm | Aligned to global regulations | Loose powder, high-filler formulas, multi-market export |
Sizes are mean particle size (D50). Calcination removes structural water and raises the refractive index, which increases coverage and the matte effect. Whiteness, oil absorption, surface area and heavy-metal and microbiological data are supplied with the batch COA. Full parameters and regulatory statements are available from KingPowder.
Manufacturing: KingPowder was founded in 2004 and is headquartered in Shanghai, with a plant of roughly 35,000 m² in Ganzhou, Jiangxi. The company holds ISO 9001 and EU REACH registration, runs powder synthesis, wet stripping, surface coating and modification, wet grinding for slurries, and jet milling and classification lines, and operates three application laboratories in Shanghai, Guangzhou and Ganzhou. Kaolin is available with AS and SI surface treatments to improve wetting in the oil phase and reduce dryness.
Verification for kaolin focuses on two things — whether the calcination was right and whether the impurity basis is right. Neither can be judged from the price, only from documents and measurements.
Whether the structural water has been removed. Calcination at high temperature removes it, densifies the crystal structure and raises the refractive index, so whiteness, coverage and adsorption all rise — in a formula that means a more definite matte, stronger oil control and better pressing, which is why it is used in pressed and loose powders. Water-washed kaolin is only desanded and purified, keeps its structural water, and has lower whiteness and coverage; it leans toward cheap filling. There is also a difference that matters in hot, humid markets: after absorbing oil, calcined material still flows well, while water-washed material turns sticky and cakes — in a product that reads as a hardened pan surface and powder that is hard to pick up.
2 µm leans toward coverage and fineness, 3 µm toward spread and cost. A smaller particle has a larger surface area, so adsorption and coverage are more pronounced, but it agglomerates more easily, disperses less well and needs more binder. Two things decide it: the proportion of other fine powders already present — if there is a lot of 2 µm-scale material, adding 2 µm kaolin makes the whole system over-fine and the pan brittle — and the target finish, where strong matte takes the finer grade and a natural translucent look takes the coarser one. The overall difference between the two is not large; in a real trial, watch batch consistency and oil absorption stability more than the size figure.
Green strength comes from mechanical interlocking and contact area between particles. Calcined kaolin is a mixed structure of platelets and irregular particles with a fine size and large surface area, so pressing produces more contact points and a denser compact. Because its surface still adheres well after absorbing oil, it holds both oil and powder and reduces spring-back and dusting. That is the thing talc cannot do: a high talc ratio makes the bulk too slippery, interlocking is lost and green strength falls instead. The matte effect comes separately from surface roughness — after calcination the surface is irregular, light scatters more diffusely and gloss drops.
5%–20% in a pressed powder; 5%–10% is enough as a pressing aid and 15%–20% as the oil-control body. Above 20% the risk of pressing failure rises sharply: the powder is too fine, oil is over-absorbed and there is not enough lubrication between particles. Work in a fixed order — check whether the dosage is too high, restore lubrication with 1%–3% magnesium stearate or more talc, then adjust the press parameters, because excessive pressure also causes spring-back and cracking. In a loose powder the ceiling is lower because the system contains little oil and kaolin supplies little slip, so too much produces drag on application.
Kaolin adsorbs oil through active sites on the particle surface and in the interlayer regions. Capacity is moderate, its adhesion stays good after absorption, and the control curve is gentle and sustained — suited to everyday base makeup, unlikely to leave skin tight. Spherical porous silica works differently: it holds oil inside its pores, has a large pore volume and reaches 150–300, so control is strong and fast — good for oily skin and long wear, but at high loadings the dryness is obvious and it can pull enough oil out of the formula to harden the bulk. Starch adsorbs through the surface and slight swelling: smooth and cheap, but limited in capacity and prone to caking.
Partly, at 30%–50% — full replacement is not recommended. Kaolin and talc overlap in platelet filling and pressing, which is what makes partial substitution work; at 30%–50% you usually get a more matte product with slightly stronger oil control and an acceptable loss of slip. Full replacement dries the formula out noticeably and the pan may become brittle from lack of lubrication. Two things have to be adjusted at the same time: restore slip with 2%–5% boron nitride or a higher mica ratio, and re-assess green strength with a drop test. If the purpose is to avoid talc-related concerns, full replacement is technically possible — but accept the cost to feel and to formula cost, and recover slip with another platelet powder.
It can, and three things usually explain it. The dosage is too high for the oil content of the base, so the powder takes up more oil than the formula can spare. The grade is too fine for the system, adding surface area that pulls oil away faster than it can be replaced. Or there is no lubricating powder alongside it — kaolin supplies no slip, so in a low-oil loose powder it reads as drag and patchiness rather than dryness alone. The fixes are to lower the dosage, pair it with boron nitride or a spherical powder, use a surface-treated grade, and move the strong oil-control requirement onto silica instead of adding more kaolin.
Work through the causes in order, because pressing failures are rarely one variable. First check the total dosage of fine absorbent powders — too much kaolin plus too much silica over-absorbs the oil and starves the binder. Then check lubrication: 1%–3% magnesium stearate, or restore some talc, which is what makes a too-slippery bulk workable in the other direction. Then check the press itself: excessive pressure causes spring-back and internal cracking, and too little gives a weak compact, so the pressure and dwell window has to be found by experiment. Finally check moisture: a high moisture content causes sticking and a dull surface, so control the storage humidity. Keep a record of pressure, dwell time and drop count so you have a baseline next time.
Ask for measured values, not a statement of conformity, and read them against the target market. Because kaolin is a natural mineral, the impurity profile follows the ore body, so a change of source has to be re-assessed even when the grade name is unchanged. Note that calcination changes the crystal phase but does not remove heavy metals — calcined is not purified, and a process description is not evidence. For products exported to several markets, set the specification against the strictest market so that one formula does not become several versions, and get the declaration in writing. Where the target market has specific requirements on lead, arsenic, mercury and cadmium, ask for the corresponding test file per batch.
They sit at different points on the same scale. Kaolin controls oil through surface and interlayer adsorption with moderate capacity, and the effect is gentle and sustained — good for daily base makeup that should not feel tight. Spherical porous silica holds oil in its pores with a large pore volume, reaching 150–300: fast and strong, suited to oily skin and long wear, but drying at high loadings and capable of pulling so much oil out that the bulk hardens. Starch adsorbs at the surface with slight swelling: smooth and inexpensive, but limited in capacity, prone to caking after absorption, and requiring preservative support. When combining them, control the total absorption — stacking all three dries a formula out very easily, which in a low-oil powder shows as drag and a cracked pan.
Beyond these, 278 answers are filed by product line in the knowledge base and can be read one by one:
Open the knowledge base →KingPowder ships samples by grade, with COA and TDS attached. Measured data for oil absorption, surface area, whiteness and heavy metals is available on request.
Phone +86 21 65683810 / 65683816 · Email sales@kingpowder.com
Request a sample and technical file →Related: Calcined kaolin grades for matte and sebum control · Cosmetic talc selection guide · Calcined kaolin questions in the knowledge base · Cosmetic powder knowledge base
© 2026 KingPowder · Technical figures on this page follow the latest COA / TDS. Information on suppliers other than KingPowder is compiled from public sources and is provided for selection reference only.
We reply within one business day with shipping arrangements and technical documents. Samples are free of charge; freight is collect or credited against your next order.