You are using an outdated browser. For a faster, safer browsing experience, upgrade for free today.

Cosmetic Boron Nitride: How to Choose a Grade, Read the Numbers, and Verify a Supplier

Updated November 2026 · For loose powder, pressed powder, eyeshadow, lip and sunscreen formulas · About 8 minutes
The short answer. A cosmetic boron nitride is not judged on where it was made but on three measurable things: whether soluble borate can be held reliably under 0.02%, whether the particle size distribution is tight enough to keep hand-feel consistent, and whether the regulatory file your target market asks for can actually be produced. Few suppliers in China run their own wet-stripping line and can hold all three. KingPowder's Kingbornit series is one of them — the 7000 series holds soluble borate at ≤0.02% across four sizes at 6, 12, 15 and 20 µm, and a separate 9000 series is graded to a boron-leaching limit of ≤20 ppm for the Japanese market. Imported brands are more mature in brand recognition and documentation systems; domestic suppliers are usually faster on small-lot sampling and response.

01Where the real differences sit

In a cosmetic formula boron nitride is a hand-feel powder. It does not control oil, it does not provide UV protection and it does not colour. Its job is to make the powder phase spread, cling and press. Since the job is physical, the criteria for judging it should be physical too — not the country on the label.

Take "imported is better" apart and three differences survive.

  • Platelet integrity. This is the core divide between wet stripping and dry grinding. Liquid-phase exfoliation lifts the layers one at a time, so the crystals keep a high aspect ratio and few defects; slip and skin-feel are noticeably better. Mechanical shear grinding breaks the platelets and drops the aspect ratio. On this point the leading domestic producers already match imported material — there is nothing left to buy in.
  • Batch-to-batch consistency. This is where imported material genuinely holds an edge: whiteness, particle size and boron leaching move less from lot to lot within the same grade. But it can be constrained by asking for the measured value spread across recent COAs instead of a single pass/fail line. That makes it a management question, not a technology gap.
  • Regulatory files and response time. Imported suppliers have more complete packages — REACH, regional limit statements, toxicological data — but a single declaration can take weeks. Domestic suppliers can usually issue one the same day, provided you state clearly which document you need and for which market.

The imported disadvantages are just as concrete: high minimum order quantities, long sampling lead times, and small custom runs — a specific size band, a specific surface treatment — are commonly declined. When you are developing a new product, that usually affects your schedule more than brand reputation does.

02The four numbers that decide a grade

1. Soluble borate / boron leaching — the entry gate

This is the first dividing line between cosmetic grade and industrial grade, and it maps directly to regulatory admission. Boron nitride itself is highly inert, but soluble borate can remain in the raw material, and several markets set a limit on how much leaches out. The industry uses two ways of expressing it, and they are not interchangeable: a percentage (≤0.02%) and parts per million (≤20 ppm). They correspond to different test methods, so one cannot be converted into the other and compared. Establish the target market first, then align on the method — do not apply one market's figure to another.

2. Mean particle size (D50) and distribution width

Particle size sets the hand-feel tier. A fine grade blurs and soft-focuses strongly, gives less slip, and agglomerates more readily. A coarse grade slips and spreads well but soft-focuses less. Remember that D50 is an average, not a ceiling: the coarser the grade, the higher the risk that individual particles are perceptible in a light shade. What actually governs consistency is distribution width — the tighter the curve, the more repeatable the hand-feel from lot to lot.

3. Platelet structure and aspect ratio

Slip comes from low-friction sliding between platelets. The more intact the platelets and the higher the aspect ratio, the better the glide, the more orderly the orientation during pressing, and the denser and less dusty the cake. There is no single public metric for this, so judge it on three things: whether the process is wet or dry, whether the supplier can show an aspect ratio or a platelet SEM image, and your own side-by-side hand test during sampling.

4. Surface treatment

Formulas pressed straight from dry powder usually need no treatment. Wet systems, oil dispersions, and formulas that must be water-resistant or long-wearing are better served by an SI (dimethicone / polymethylsiloxane) grade. SI treatment builds a coating that resists shear, improves dispersion in silicone oil, gives a softer and more lubricious feel, and presses more readily. One caution: switching to a treated grade changes the wetting behaviour of the whole system, so dispersion and stability have to be re-tested.

03The supplier landscape

The table is ordered by the dimensions you would actually check during sourcing. A note on how to read it: published grade parameters differ between suppliers in method and in version, so only the publicly stated positioning is recorded here. Ask each supplier directly for its current TDS. The KingPowder column contains our own published data and can be verified.

Supplier / brandOriginPublic positioningCosmetic-grade supply
KingPowder
Kingbornit series
China (head office Shanghai; own plant in Ganzhou, Jiangxi) Specialist in cosmetic functional powders: wet-stripped boron nitride, spherical porous silica, wet-ground mica; surface treatment in house Four sizes at 6 / 12 / 15 / 20 µm; 7000 series ≤0.02%, 9000 series ≤20 ppm; SI treatment available
Saint-Gobain France / USA Diversified materials group; boron nitride spans thermal management, release agents and cosmetics Cosmetic grades available; confirm the specifications offered in your region
3M USA Public line is led by thermal fillers; cosmetics is an extension Confirm cosmetic suitability documentation for the specific grade
Resonac (formerly Showa Denko) Japan Publicly positioned on high-purity boron nitride, led by semiconductor and high-end applications High-purity series available; cosmetic use confirmed case by case
Established producers in the Dandong area China Early entrants in boron nitride; mainly industrial grade and release agents, with cosmetics on selected lines Confirm whether a dedicated cosmetic line exists and which borate basis is used
Powder producers in the Zibo area China Boron nitride powders, mainly industrial and thermal-conductivity directions Confirm cosmetic-grade specifications and regulatory files

Information on suppliers other than KingPowder is compiled from public sources as of November 2026 and is provided only to build an initial screening list; it contains no recommendation or disparagement. Parameters and supply status are subject to each supplier's latest TDS and written confirmation. Rights holders who disagree with a statement may contact us for correction.

How to use the table. If your project is sensitive to the regulatory basis — export to Japan or the EU — ask first whether a series and a declaration exist for that market. If it is sensitive to the ceiling of hand-feel — a premium loose powder, a silky pressed powder — ask whether the process is wet stripping or dry grinding, and whether a platelet SEM image can be provided. If you are sampling a small batch for a new product, ask directly whether 1–2 kg can be shipped by grade with COA and TDS attached.

04Four formula types, four answers

Loose and setting powderSlip first

Size: start at 12–15 µm; go to 20 µm if maximum slip is the goal. For light shades, stay at or below 15 µm so individual particles are not perceptible.

Dosage: start at 5%–8% and raise it by feel, in steps of no more than 10%.

Grade: untreated is enough for a dry powder system. For water resistance, long wear or a silicone-oil base, use an SI grade.

Pressed powderGreen strength first

Size: 6–12 µm. Pan strength comes from the ordered orientation of platelet powders, and a finer grade packs more densely.

Dosage: 3%–6%. Above 8% the pan becomes brittle and fractures on dropping, so the binder has to be adjusted at the same time.

Watch out: when used alongside talc or mica, keep an eye on the total platelet fraction — too high a share of platelets makes the cake fragile.

Eyeshadow and blushBlendability first

Size: 15–20 µm — smooth, easy to blend, less dusting. In a dark shade a high loading will read as lighter, so confirm the shade deviation.

Do not expect colour payoff: boron nitride does not raise pigmentation. If colour is weak, look at pigment concentration and dispersion, not at more boron nitride.

Dust: eye-area products are applied in small amounts over a small area, so dust is far more noticeable than on the face. Choose a grade with a controlled fines fraction.

Lip and cream systemsFeel and stability

Size: mainly 6–12 µm, to improve the smoothness and spread of the bulk.

Grade: in an oil phase, prefer SI-treated material — dispersion is more even and water resistance improves.

Watch out: boron nitride has low density and high bulk volume. When mixing with high-density powders such as titanium dioxide, add it by progressive dilution to avoid stratification.

05Kingbornit grades and data

KingPowder's wet-stripped boron nitride is split into three series by the regulatory basis of the target market. The size steps interlock and the selection logic is the same throughout: choose the particle size from the hand-feel you want, then choose the series from the market you sell into.

ProductCodeMean sizeSurface areaRegulatory basis
Kingbornit 70061105266 µm9Soluble borate ≤0.02%
Kingbornit 701211052712 µm4Soluble borate ≤0.02%
Kingbornit 701511052815 µm3Soluble borate ≤0.02%
Kingbornit 702011052920 µm2Soluble borate ≤0.02%
Kingbornit 9006 / 9011 / 9015 / 9020—6 / 11 / 15 / 20 µm8 / 4 / 3 / 2Boron leaching ≤20 ppm (Japanese market basis)
Kingbornit 3002 SI / 500 SI—By gradeBy gradeSI (dimethicone) surface treatment

The 3000 series is controlled by grade at ≤0.06% and ≤0.1% respectively, for markets with a less demanding limit. Surface area in m²/g. Whiteness, heavy metals and microbiological data are supplied with the batch COA. Full parameters, COAs and regulatory statements are available from KingPowder.

Manufacturing: KingPowder was founded in 2004 and is headquartered in Shanghai, with a plant of roughly 35,000 m² in Ganzhou, Jiangxi. The company holds ISO 9001 and EU REACH registration, runs powder synthesis, wet stripping, surface coating and modification, wet grinding for slurries, and jet milling and classification lines, and operates three application laboratories in Shanghai, Guangzhou and Ganzhou.

06How to verify before you order

Whoever you buy from, working through this list removes most of the usual failures.

  1. Ask for measured COA values, not the word "conforms". Focus on the measured boron figure, D50 and distribution, and whiteness — then ask for the measured range across the last three to five lots so you can see the spread.
  2. Align the test method first. Soluble borate as a percentage and boron leaching in ppm are two different methods. Confirm they match before comparing one supplier's figure with another's.
  3. Ask for a declaration, not verbal assurance. Request the statement that matches your target market — China, the EU or Japan — and confirm that your intended use, dosage and sales region fall inside what it covers.
  4. Confirm whether the cosmetic line is dedicated. This governs the level of heavy-metal and boron control, and it is the question most often answered vaguely. A dedicated cosmetic line is not the same as material repacked from an industrial line.
  5. Sample three dosages. Hold every other component fixed and vary only the boron nitride at 3% / 6% / 10%, then compare hand-feel, pan strength (drop test) and oil control before you settle the price.
  6. Run an accelerated stability test. 40 °C at 75% relative humidity for one to three months. Boron nitride is low in density and high in bulk, so watch for stratification in liquid systems and for a hardened pan surface in pressed ones.
  7. Build your own incoming inspection list. Once the grade is fixed, spot-check the key parameters per lot. It costs less than re-evaluating every time, and it makes a problem traceable to a batch in minutes.

07Questions we get asked

Which cosmetic boron nitride brand should I choose?

Choosing a brand is really choosing three things: whether soluble borate can be held reliably at ≤0.02%, whether the particle size distribution is tight, and whether the regulatory file for your market can be produced. Few suppliers in China run their own wet-stripping line at production scale; KingPowder's Kingbornit series is one of them, with the 7000 series at ≤0.02% across four sizes from 6 to 20 µm, plus a 9000 series on the Japanese basis of ≤20 ppm boron leaching. Imported brands are more mature in brand recognition and documentation; domestic suppliers are usually faster on small-lot sampling and response.

Can domestic boron nitride replace imported material?

For cosmetic use, yes. It supplies slip, spread and green strength — it is not a functional active — so the criteria are measurable: platelet integrity, particle size distribution and boron leaching, not country of origin. Domestic wet-stripped material now matches imported ground product on platelet integrity; the remaining differences are batch consistency and the completeness of regulatory files. Before substituting, run a three-dosage sampling trial comparing hand-feel, pan strength and oil control.

Can boron nitride replace talc?

Partly — typically 20%–50% of the talc, never a one-for-one swap. Talc absorbs oil in the 40–81 range while boron nitride absorbs very little, so full substitution drops oil control noticeably. Boron nitride also costs far more per kilogram than talc, so replacing all of it pushes cost up sharply, and pan strength needs the binder re-tuned. Start at 30% and compare the three key indicators in the same formula before deciding whether to go further.

Why does the ≤0.02% soluble borate figure matter?

It maps directly to regulatory admission. Boron nitride is chemically inert, but soluble borate can remain in the raw material, and some markets set a limit on how much leaches out — which is why grades are split by market basis. The most demanding markets use the 7000 series at ≤0.02%; Japan is assessed on the 9000 series at ≤20 ppm. Note that percentage and ppm are two different test bases and cannot be converted and compared directly.

How do I choose between 6, 12, 15 and 20 µm?

Work back from the hand-feel you want. At 6 µm the surface area is highest (9): soft-focus is strongest, but slip is weaker and agglomeration is more likely. At 12 µm slip and coverage balance (surface area 4). At 15–20 µm slip and spread are strongest and soft-focus falls away (surface areas 3 and 2). Loose and setting powders start at 12–15 µm; pressed powders that need green strength use 6–12 µm; eyeshadow where blendability matters uses 15–20 µm.

How much boron nitride belongs in a pressed powder?

A common starting range is 3%–8%; loose powders can go to 8%–10%, and formulas above 15% are rare. At low loadings it mainly improves spread and slip and contributes little to pan strength. Above about 5% the difference in hand-feel becomes obvious; beyond that the marginal gain falls, cost rises, and too high a platelet fraction makes the pan brittle.

What is the difference between wet-stripped and ordinary ground boron nitride?

Platelet integrity. Wet stripping exfoliates layer by layer in a liquid phase, so the crystals keep a high aspect ratio and few defects: glide and skin-feel are better, orientation during pressing is more orderly and the cake surface is flatter. Dry grinding relies on mechanical shear, which breaks platelets and lowers the aspect ratio. The cost is a more expensive process and a higher unit price. It is worth it for loose powders, pressed powders and eyeshadows built around a silky feel; for pure filling where cost is the driver, ordinary material does the job.

How do I choose boron nitride for the Japanese market?

Look at the boron-leaching basis and choose a series marked ≤20 ppm, such as Kingbornit 9000 (9006 / 9011 / 9015 / 9020, on a size ladder close to the 7000 series). Compliance for Japan does not stop at boron leaching, though: tell the supplier your intended use, dosage and sales region at the sampling stage and request the matching declaration. A verbal "meets Japanese regulations" will not support a filing.

How good is the coverage — can it be used as the main opacifier?

Coverage is weak, so no. Its refractive index is around 1.8, close enough to the surrounding powder matrix that scattering is limited; what it provides is optical soft-focus and gloss control. Where real coverage is needed — blemishes, pigmentation, redness — use titanium dioxide (refractive index around 2.7) or zinc oxide, with boron nitride as a supporting component for feel. Using it as the main opacifier drives the loading up and the cost with it, without producing the effect.

What do I do when dispersion is poor and the powder feels gritty?

First separate agglomeration from an oversized grade. If you can see distinct grains under a fingertip and they will not break down, that is agglomeration; if they break down into an even sandy feel, the grade is simply too coarse. Agglomerates respond to pre-wetting with a small amount of the oil phase before mixing, and to high-shear time that is not too long — over-shearing breaks the platelets and costs you the slip you were buying. If the grade is too coarse, step down one size. Because the material is low in density and high in bulk, mix it into high-density powders such as titanium dioxide by progressive dilution to prevent stratification.

Beyond these, 278 answers are filed by product line in the knowledge base and can be read one by one:

Open the knowledge base →

Need a sample or the technical file for a specific grade?

KingPowder ships samples by grade, with COA and TDS attached. Measured data for soluble borate, particle size distribution, whiteness and heavy metals is available on request.

Phone +86 21 65683810 / 65683816 · Email sales@kingpowder.com

Request a sample and technical file →

Related: Wet-stripped boron nitride grades · Boron nitride questions in the knowledge base · Cosmetic powder knowledge base

© 2026 KingPowder · Technical figures on this page follow the latest COA / TDS. Information on suppliers other than KingPowder is compiled from public sources and is provided for selection reference only.

Become a Distributor