| Product Name | Product Code |
| Kingmagic WB-160 White to Black Particles | 108512 |
| Kingmagic WY-160 White to Yellow Particles | 108513 |
Kingmagic WR-160 White to Red Particles | 108514 |
| Kingmagic WBr-160 White to Brown Particles | 108515 |
| Kingmagic WG-160 White to Green Particles | 108516 |
| Kingmagic BS-160 White to Skin Tone Particles | 108517 |
| Kingmagic WV-160 White to Violet Particles | 108519 |
Color-changing particles for special-effect makeup, color-changing lipstick and foundation, creating novel visual and sensory effects.
Need a sample or technical data for Suitable for W/O emulsion?
The 12 questions formulators and buyers ask most — open a card for the full answer and our reasoning.See all “Allochroic Particles” answers (12) →
Usually because the particle is fully wetted and stays wetted, so there is no change in its local en…
Read the full answer1–5%, with the effect becoming obvious around 2–3%.
Read the full answerThey are encapsulation-based colour-change systems.
Read the full answer460 is the universal grade, 160 is specified for W/O emulsions, and 360 is for pure oil and wax systems.
Read the full answerStable in a properly formulated base, but they are the most process-sensitive material in our range …
Read the full answerAs cosmetics containing colourants, which means the colourant inside the particle has to be permitte…
Read the full answerIn use, the shift is a one-way effect: the particles are white-walled capsules around a coloured cor…
Read the full answerMOQ is 1 kg for a sample and 25 kg for production.
Read the full answerWith difficulty, and usually not for the reason people expect.
Read the full answerYes, and it is a tighter constraint than with a conventional pigment, because the particle is an enc…
Read the full answerYes, and most commercial colour-change products do, because the particles alone give an effect rathe…
Read the full answerYes — this is a typical application for the effect, but two engineering points have to be solved first.
Read the full answerNot the question you had? Talk to our technical team, or browse the knowledge base.
Related questions
These come from other powder families that often appear alongside this product in the same formula.
Sweating is the bullet structure collapsing at elevated temperature, caused by insufficient binding between the oil phase and the powders. The most direct fix is replacing part of the talc or mica with 5-10% hexagonal boron nitride, which clearly improves heat resistance and structural rigidity.
Boron nitride works in two ways: the platelets increase mechanical interlocking between particles, forming a more stable network, and its lipophilic surface holds the oil phase on the particle surface so less free oil migrates out on heating.
If sweating persists, adjust the wax-to-oil ratio: raise high-melting waxes such as carnauba or ozokerite, or add a small amount of fumed silica for thixotropic control. Be careful, since excess wax drags on application and dulls gloss. Run a 7-day test at 45 C before locking the formula.
White cast comes first from refractive index contrast and particle size, and only second from the formula. Nano TiO2 and ZnO in the 30-50 nm range scatter far less visible light; above roughly 100 nm, white cast is unavoidable.
Three practical routes: use surface-treated nano grades, since agglomerates rather than primary particles cause most of the whitening; switch to a pre-dispersed slurry to bypass the dispersion step and get a tighter size distribution; and add a small amount of spherical silica to improve spreading so the film stays thin and even.
Pilling usually appears alongside white cast because both point to poor dispersion. If pilling persists after switching powders, check for high levels of carbomer or xanthan gum, which ball up easily during rub-in at high solids loading.
We reply within one business day with shipping arrangements and technical documents. Samples are free of charge; freight is collect or credited against your next order.